Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001T4LN
Model Year Start: 2021 Model: Camry HV Prod Date Range: [10/2020 -           ]
Title: A25A-FXS (FUEL): FUEL INJECTOR (for Port Injection): REMOVAL; 2021 - 2024 MY Camry HV [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Tracing Assist System

2021 - 2024 MY Camry HV [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic View Monitor System

2021 - 2024 MY Camry HV [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Replacement of inverter with converter assembly

Resolver learning

  • DTCs are stored
  • Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
  • Shock or vibration during acceleration

2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): UTILITY for Nickel Metal Hydride Battery

2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY): UTILITY for Lithium-ion Battery

Replacement of ECM

Perform Vehicle Identification Number (VIN) registration

MIL illuminates

2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

  • Replacement of port fuel injector assembly
  • Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)
  • Replacement of throttle body with motor assembly
  • Cleaning the deposits from the throttle body with motor assembly
  • Replacement of EGR valve assembly
  • Gas leak from exhaust system is repaired

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

CAUTION:

  • Never perform work on fuel system components near any possible ignition sources.
  • Vaporized fuel could ignite, resulting in a serious accident.
  • Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
  • To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCHARGE FUEL SYSTEM PRESSURE

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (FUEL): FUEL SYSTEM: PRECAUTION

3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2021 - 2022 MY Camry HV [10/2020 - 08/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2023 - 2024 MY Camry HV [08/2022 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

5. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (ENGINE CONTROL): THROTTLE BODY: REMOVAL

6. REMOVE EGR VALVE ASSEMBLY

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (EMISSION CONTROL): EGR VALVE: REMOVAL

7. REMOVE NO. 2 WATER BY-PASS PIPE

Click here 2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (INTAKE / EXHAUST): INTAKE MANIFOLD: REMOVAL+

8. DISCONNECT FUEL TUBE SUB-ASSEMBLY

(a) Remove the fuel pipe clamp from the fuel tube connector.

(b) Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (FUEL): FUEL SYSTEM: PRECAUTION

9. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

(a) Disconnect the ignition coil connector.

(b) for EGR Valve Bracket Connection Type:

(1) Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.

(c) for Cylinder Head Cover Sub-assembly Connection Type:

(1) Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.

Union Nut

Bolt

(2) Using an 8 mm socket wrench, remove the bolt.

(d) Loosen the 2 bolts of the fuel pump assembly.

(e) Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.

10. REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

(a) Disconnect the No. 5 engine wire connector.

(b) Remove the 2 bolts and fuel delivery pipe with sensor assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

  • If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
  • Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.

11. REMOVE NO. 1 DELIVERY PIPE SPACER

(a) Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.

12. REMOVE INJECTOR VIBRATION INSULATOR

(a) Remove the 4 injector vibration insulators from the cylinder head sub-assembly.

13. REMOVE NO. 5 ENGINE WIRE

(a) Disconnect the 4 port fuel injector assembly connectors and fuel pressure sensor connector.

(b) Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe with sensor assembly.

14. REMOVE PORT FUEL INJECTOR ASSEMBLY

(a) Pull the 4 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.

(b) Remove the O-ring from each port fuel injector assembly.

(c) Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.