| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001RX1O |
| Model Year Start: 2021 | Model: Camry HV | Prod Date Range: [10/2020 - ] |
| Title: CRUISE CONTROL: FRONT CAMERA SYSTEM: C1AA800; Front Recognition Camera Optical Axis Misalignment Malfunction; 2021 - 2024 MY Camry HV [10/2020 - ] | ||
|
DTC |
C1AA800 |
Front Recognition Camera Optical Axis Misalignment Malfunction |
DESCRIPTION
The forward recognition camera monitors its optical axis status. If it determines that the optical axis alignment has become misaligned, it will store DTC C1AA800.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AA800 |
Front Recognition Camera Optical Axis Misalignment Malfunction |
3 seconds or more after the power switch is turned on (IG), the forward recognition camera detects an optical axis misalignment when the vehicle is being driven at a speed of 5 km/h (4 mph) or more. |
|
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
-
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
![2021 - 2024 MY Camry HV [10/2020 - ]; CRUISE CONTROL: FRONT CAMERA: TARGET ADJUSTMENT(ONE TIME RECOGNITION)](/t3Portal/stylegraphics/info.gif)
Sequential Recognition: Click here
Driving Adjustment: Click here
- When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the forward recognition camera may not operate properly due to a difference in the transmissivity or black ceramic border.
- Forward recognition camera optical axis may deviate if the vehicle is driven on a banked road, such as a racetrack. This deviation can be corrected by driving the vehicle on a normal road for a while.
- Forward recognition camera optical axis may deviate when the vehicle is overloaded or the wheel alignment (toe-in) is incorrect. The forward recognition camera optical axis can be corrected by decreasing the load on the vehicle or adjusting the toe-in.
PROCEDURE
|
1. |
CHECK FORWARD RECOGNITION CAMERA INSTALLATION |
Click here
HINT:
If there is deformation or deviation in the forward recognition camera installation bracket, replace the windshield glass.
OK:
No deformation or deviation in forward recognition camera installation bracket.
| NG |
|
|
|
2. |
CHECK VEHICLE OPERATING CONDITION |
HINT:
Check if a condition which caused the forward recognition camera optical axis to become temporarily misaligned existed, such as if the vehicle was overloaded, towed or modified.
OK:
Vehicle was not overloaded, towed or modified.
| NG |
|
|
|
3. |
CHECK WHEEL ALIGNMENT (TOE) |
-
for Front Wheel Alignment: Click here
-
for Rear Wheel Alignment: Click here
OK:
Front and rear wheels are not misaligned (toe)
| NG |
|
|
|
4. |
PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
Sequential Recognition: Click here
Driving Adjustment: Click here
|
|
5. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs
| NEXT |
|
END |
|
6. |
ADJUST WHEEL ALIGNMENT (TOE) |
-
for Front Wheel Alignment: Click here
-
for Rear Wheel Alignment: Click here
|
|
7. |
PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
Sequential Recognition: Click here
Driving Adjustment: Click here
|
|
8. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs
| NEXT |
|
END |
|
9. |
PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
(a) Return the vehicle to normal operating conditions.
(b) Perform forward recognition camera adjustment.
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
Sequential Recognition: Click here
Driving Adjustment: Click here
|
|
10. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs
| NEXT |
|
END |
|
11. |
REPLACE WINDSHIELD GLASS |
Click here
|
|
12. |
PERFORM FORWARD RECOGNITION CAMERA ADJUSTMENT |
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
Sequential Recognition: Click here
Driving Adjustment: Click here
|
|
13. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Front Recognition Camera > Clear DTCs
| NEXT |
|
END |
|
|