| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001LCK8 |
| Model Year Start: 2020 | Model: Camry HV | Prod Date Range: [09/2019 - ] |
| Title: CELLULAR COMMUNICATION: SAFETY CONNECT SYSTEM: B157213; Microphone Circuit Open; 2020 - 2024 MY Camry HV [09/2019 - ] | ||
|
DTC |
B157213 |
Microphone Circuit Open |
DESCRIPTION
This DTC is stored when the DCM (telematics transceiver) detects a malfunction in the telephone microphone assembly circuit.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B157213 |
Microphone Circuit Open |
Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the power switch is on (IG) |
|
WIRING DIAGRAM
w/ Sliding Roof
w/o Sliding Roof
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Safety Connect System.
Click here
![2020 MY Camry HV [09/2019 - 10/2020]; CELLULAR COMMUNICATION: SAFETY CONNECT SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK DTC |
(a) Turn the power switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG) and wait for 10 seconds or more.
(d) Turn the Techstream on.
(e) Clear the DTCs.
Body Electrical > Telematics > Clear DTCs
(f) Check for DTCs and check that no DTCs are output.
Body Electrical > Telematics > Trouble Codes
OK:
No DTCs are output.
| OK |
|
USE SIMULATION METHOD TO CHECK
|
|
|
2. |
CONFIRM MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
w/ Sliding Roof |
A |
|
w/o Sliding Roof |
B |
| B |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Disconnect the K140 DCM (telematics transceiver) connector.
(b) Disconnect the V14 roof console box sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K140-5 (MCVD) - V14-9 (MACC) |
Always |
Below 1 Ω |
|
K140-6 (MCI+) - V14-8 (MCO+) |
Always |
Below 1 Ω |
|
K140-7 (MCI-) - V14-7 (MCO-) |
Always |
Below 1 Ω |
|
K140-23 (SGND) - Body ground |
Always |
10 kΩ or higher |
|
K140-5 (MCVD) or V14-9 (MACC) - Body ground |
Always |
10 kΩ or higher |
|
K140-6 (MCI+) or V14-8 (MCO+) - Body ground |
Always |
10 kΩ or higher |
|
K140-7 (MCI-) or V14-7 (MCO-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK DCM (TELEMATICS TRANSCEIVER) (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE) |
|
(a) Remove the telephone microphone assembly but do not disconnect the connectors. Click here
|
|
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
V14-9 (MACC) - Body ground |
Power switch on (ACC) |
4 to 6 V |
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
V14-7 (MCO-) - Body ground |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
|
5. |
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Disconnect the K140 DCM (telematics transceiver) connector.
(b) Disconnect the V18 roof console box sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K140-5 (MCVD) - V18-6 (MACC) |
Always |
Below 1 Ω |
|
K140-6 (MCI+) - V18-5 (MCO+) |
Always |
Below 1 Ω |
|
K140-7 (MCI-) - V18-4 (MCO-) |
Always |
Below 1 Ω |
|
K140-23 (SGND) - Body ground |
Always |
10 kΩ or higher |
|
K140-5 (MCVD) or V18-6 (MACC) - Body ground |
Always |
10 kΩ or higher |
|
K140-6 (MCI+) or V18-5 (MCO+) - Body ground |
Always |
10 kΩ or higher |
|
K140-7 (MCI-) or V18-4 (MCO-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
CHECK DCM (TELEMATICS TRANSCEIVER) (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE) |
|
(a) Remove the roof console box sub-assembly but do not disconnect the connectors. Click here
|
|
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
V18-6 (MACC) - Body ground |
Power switch on (ACC) |
4 to 6 V |
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
V18-4 (MCO-) - Body ground |
Always |
Below 1 Ω |
| OK |
|
|
|
7. |
REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (telematics transceiver) with a new one.
Click here
NOTICE:
- The power switch must be off
- Do not exchange the DCM (telematics transceiver) with one from another vehicle.
| NEXT |
|
|
|