EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2020 MY Camry HV [09/2019

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM100000001L5ES
Model Year Start: 2020	Model: Camry HV	Prod Date Range: [09/2019 - 10/2020]
Title: EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2020 MY Camry HV [09/2019 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative auxiliary battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
		Lighting system (w/ AFS)(EXT)
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Front door glass sub-assembly	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Click here

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here

5. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here

6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

8. REMOVE FRONT ARMREST ASSEMBLY

Click here

9. REMOVE FRONT DOOR TRIM PLATE (w/o Courtesy Light)

Click here

10. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Click here

11. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Click here

13. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here

14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here

15. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

(a) Apply protective tape around the front door belt moulding assembly as shown in the illustration.

Protective Tape

(b) Disengage the 5 claws as shown in the illustration.

*a	Claw
	Rotate in this Direction

(c) Using a thin-bladed screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.

*a	Thin-bladed Screwdriver with its Tip Wrapped with Protective Tape
	Push in this Direction

(d) Slightly twist and hold the front door belt moulding assembly in the direction indicated by the arrow (1) shown in the illustration.

Twist in this Direction (1)

Slide in this Direction (2)

NOTICE:

If the front door belt moulding assembly is pulled upwards, the claw may break and fall inside the door panel.

(e) Slide the front door belt moulding assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the claw and remove the front door belt moulding assembly.