Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM100000001KY84 |
Model Year Start: 2020 |
Model: Camry HV |
Prod Date Range: [09/2019 -
] |
Title: LIGHTING (EXT): LIGHTING SYSTEM (w/ AFS): B2424,B2425; Headlight Beam Level Control Motor LH Lost Communication; 2020 - 2024 MY Camry HV [09/2019 - ] |
DTC
|
B2424
|
Headlight Beam Level Control Motor LH Lost Communication
|
DTC
|
B2425
|
Headlight Beam Level Control Motor RH Lost Communication
|
DESCRIPTION
Each headlight ECU sub-assembly and headlight swivel and leveling motor communicate via LIN communication.
The headlight swivel and leveling motor operates according to power supplied and automatic headlight beam level control signals from its respective headlight ECU sub-assembly and sends its operating state to the headlight ECU sub-assembly.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
DTC Output from
|
B2424
|
Headlight Beam Level Control Motor LH Lost Communication
|
Detection condition:
-
The power switch is on (IG).
|
-
Headlight assembly LH
-
Headlight assembly RH
-
Harness or connector
-
Headlight ECU sub-assembly LH
-
Headlight ECU sub-assembly RH
|
AFS
|
B2425
|
Headlight Beam Level Control Motor RH Lost Communication
|
Detection condition:
-
The power switch is on (IG).
|
-
Headlight assembly RH
-
Headlight assembly LH
-
Harness or connector
-
Headlight ECU sub-assembly RH
-
Headlight ECU sub-assembly LH
|
AFS
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(e) Clear the DTCs.
Body Electrical > AFS > Clear DTCs
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Wait 10 seconds or more.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(f) Check for DTCs.
Body Electrical > AFS > Trouble Codes
OK:
DTC B2424 and B2425 are not output.
Result
|
Proceed to
|
OK
|
A
|
NG (DTC B2424 is output)
|
B
|
NG (DTC B2425 is output)
|
C
|
NG (DTC B2424 and B2425 are output)
|
D
|
B
|
|
|
3.
|
CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
|
(a) Replace the headlight ECU sub-assembly LH with a new or known good one.
Click here
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(e) Clear the DTCs.
Body Electrical > AFS > Clear DTCs
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Wait 10 seconds or more.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(f) Check for DTCs.
Body Electrical > AFS > Trouble Codes
OK:
DTC B2424 is not output.
OK |
|
END (HEADLIGHT ECU SUB-ASSEMBLY LH WAS DEFECTIVE)
|
6.
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)
|
(a) Disconnect the A79 headlight ECU sub-assembly LH connector.
(b) Disconnect the A80 headlight ECU sub-assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A79-20 (LINL) - A80-20 (LINL)
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
7.
|
CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (LINL TERMINAL SIGNAL OUTPUT)
|
*a
|
Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)
|
(a) Connect the A79 headlight ECU sub-assembly LH connector.
(b) Using a Techstream, check the waveform.
OK:
Tester Connection
|
Condition
|
Specified Condition
|
A80-20 (LINL) - Body ground
|
Power switch on (IG)
|
Pulse generation
|
OK
|
|
|
8.
|
INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH
|
*a
|
Component without harness connected
(Headlight ECU Sub-assembly RH)
|
-
|
-
|
(a) Remove the headlight ECU sub-assembly RH.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A80-20 (LINL) - C-13 (LINLI)
|
Always
|
Below 1 Ω
|
9.
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)
|
(a) Disconnect the A79 headlight ECU sub-assembly LH connector.
(b) Disconnect the A80 headlight ECU sub-assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A79-20 (LINL) or A80-20 (LINL) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
(a) Connect the A79 headlight ECU sub-assembly LH connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(f) Clear the DTCs.
Body Electrical > AFS > Clear DTCs
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Wait 10 seconds or more.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(f) Check for DTCs.
Body Electrical > AFS > Trouble Codes
Result
|
Proceed to
|
DTC B2425 is output
|
A
|
DTC B2424 and B2425 are output
|
B
|
A
|
|
|
12.
|
CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
|
(a) Remove the headlight ECU sub-assembly RH from headlight assembly RH.
Click here
(b) Connect the A80 headlight ECU sub-assembly RH connector.
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(e) Clear the DTCs.
Body Electrical > AFS > Clear DTCs
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Wait 10 seconds or more.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(f) Check for DTCs.
Body Electrical > AFS > Trouble Codes
Result
|
Proceed to
|
DTC B2425 is output
|
A
|
DTC B2424 and B2425 are output
|
B
|
15.
|
CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
|
(a) Remove the headlight ECU sub-assembly LH from headlight assembly LH.
Click here
(b) Connect the A79 headlight ECU sub-assembly LH connector.
(c) Connect the A80 headlight ECU sub-assembly RH connector.
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(e) Clear the DTCs.
Body Electrical > AFS > Clear DTCs
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Wait 10 seconds or more.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / AFS / Trouble Codes.
(f) Check for DTCs.
Body Electrical > AFS > Trouble Codes
Result
|
Proceed to
|
DTC B2424 is output
|
A
|
DTC B2424 and B2425 are output
|
B
|
|