Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001KN38
Model Year Start: 2020 Model: Camry HV Prod Date Range: [09/2019 -           ]
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Microphone Circuit between Microphone and Radio Receiver; 2020 - 2024 MY Camry HV [09/2019 -        ]

Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION

  • w/o Manual (SOS) Switch:

    The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

    Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

  • w/ Manual (SOS) Switch:

    The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

    Using this circuit, the DCM (telematics transceiver) sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the DCM (telematics transceiver).

WIRING DIAGRAM

w/ Sliding Roof
w/o Sliding Roof

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.
  • Before replacing the DCM (telematics transceiver), refer to Registration.

    Click here 2020 - 2022 MY Camry HV [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

PROCEDURE

1.

CHECK MODEL

(a) Choose the model to be inspected.

Result

Proceed to

w/ Sliding Roof

A

w/o Sliding Roof

B

B

GO TO STEP 19

A

2.

CHECK MICROPHONE (OPERATION CHECK)

(a) Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click here 2020 MY Camry HV [09/2019 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK

(b) When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.

Result

Proceed to

NG (w/o Manual (SOS) Switch)

A

NG (w/ Manual (SOS) Switch)

B

OK

C

B

GO TO STEP 9

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

A

3.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

(a) Disconnect the K2 radio and display receiver assembly connector.

(b) Disconnect the V14 roof console box sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-25 (SNS2) - V14-6 (SNS2)

Always

Below 1 Ω

K2-23 (MACC) - V14-9 (MACC)

Always

Below 1 Ω

K2-21 (MIN+) - V14-8 (MCO+)

Always

Below 1 Ω

K2-22 (MIN-) - V14-7 (MCO-)

Always

Below 1 Ω

K2-25 (SNS2) or V14-6 (SNS2) - Body ground

Always

10 kΩ or higher

K2-23 (MACC) or V14-9 (MACC) - Body ground

Always

10 kΩ or higher

K2-21 (MIN+) or V14-8 (MCO+) - Body ground

Always

10 kΩ or higher

K2-22 (MIN-) or V14-7 (MCO-) - Body ground

Always

10 kΩ or higher

K2-24 (SGND) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V14 roof console box sub-assembly connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K2-23 (MACC) - Body ground

Power switch on (ACC)

4 to 6 V

*a

Component with harness connected

(Radio and Display Receiver Assembly)

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-24 (SGND) - Body ground

Always

Below 1 Ω

K2-22 (MIN-) - Body ground

Always

Below 1 Ω

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

OK

5.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Connect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

6 (SNS2) - 7 (MCO-)

Always

Below 1 Ω

*a

Component without harness connected

(Roof Console Box Sub-assembly)

NG

GO TO STEP 8

OK

6.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V14 roof console box sub-assembly connector.

(c) Turn the power switch on (ACC).

(d) Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.

*a

Component with harness connected

(Roof Console Box Sub-assembly)

(e) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

V14-8 (MCO+) - V14-7 (MCO-)

Tool setting

50 mV/DIV., 500 ms/DIV.

Vehicle condition

  1. Turn the power switch on (ACC).
  2. Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.

OK:

The waveform is similar to that shown in the illustration.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2020 MY Camry HV [09/2019 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE

NG

7.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V14-8 (MCO+) - B-3

Always

Below 1 Ω

V14-7 (MCO-) - B-2

Always

Below 1 Ω

V14-8 (MCO+) or B-3 - V14-15 (GND)

Always

10 kΩ or higher

V14-7 (MCO-) or B-2 - V14-15 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

8.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V14-6 (SNS2) - B-1

Always

Below 1 Ω

V14-7 (MCO-) - B-2

Always

Below 1 Ω

V14-6 (SNS2) or B-1 - V14-15 (GND)

Always

10 kΩ or higher

V14-7 (MCO-) or B-2 - V14-15 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

9.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

(a) Disconnect the K2 radio and display receiver assembly connector.

(b) Disconnect the V14 roof console box sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-25 (SNS2) - V14-6 (SNS2)

Always

Below 1 Ω

K2-25 (SNS2) or V14-6 (SNS2) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

10.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))

(a) Disconnect the K2 radio and display receiver assembly connector.

(b) Disconnect the K140 DCM (telematics transceiver) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-21 (MIN+) - K140-16 (MCO+)

Always

Below 1 Ω

K2-22 (MIN-) - K140-32 (MCO-)

Always

Below 1 Ω

K2-21 (MIN+) or K140-16 (MCO+) - Body ground

Always

10 kΩ or higher

K2-22 (MIN-) or K140-32 (MCO-) - Body ground

Always

10 kΩ or higher

K2-24 (SGND) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

11.

CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY)

(a) Disconnect the K140 DCM (telematics transceiver) connector.

(b) Disconnect the V14 roof console box sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K140-6 (MCVD) - V14-9 (MACC)

Always

Below 1 Ω

K140-5 (MCI+) - V14-8 (MCO+)

Always

Below 1 Ω

K140-7 (MCI-) - V14-7 (MCO-)

Always

Below 1 Ω

K140-6 (MCVD) or V14-9 (MACC) - Body ground

Always

10 kΩ or higher

K140-5 (MCI+) or V14-8 (MCO+) - Body ground

Always

10 kΩ or higher

K140-7 (MCI-) or V14-7 (MCO-) - Body ground

Always

10 kΩ or higher

K140-23 (SGND) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

12.

INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect the K12 DCM (telematics transceiver) connector.

(b) Connect the K2 radio and display receiver assembly connector.

*a

Component with harness connected

(Radio and Display Receiver Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-24 (SGND) - Body ground

Always

Below 1 Ω

K2-22 (MIN-) - Body ground

Always

Below 1 Ω

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

OK

13.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Connect the K140 DCM (telematics transceiver) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K140-33 (MCVD) - Body ground

Power switch on (ACC)

4 to 6 V

*a

Component with harness connected

(DCM (Telematics Transceiver))

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K140-35 (MCI-) - Body ground

Always

Below 1 Ω

K140-32 (SGND) - Body ground

Always

Below 1 Ω

NG

REPLACE DCM (TELEMATICS TRANSCEIVER) 2020 MY Camry HV [09/2019 - 10/2020]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

OK

14.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Connect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

6 (SNS2) - 7 (MCO-)

Always

Below 1 Ω

*a

Component without harness connected

(Roof Console Box Sub-assembly)

NG

GO TO STEP 18

OK

15.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO DCM (TELEMATICS TRANSCEIVER))

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V14 roof console box sub-assembly connector.

(c) Connect the K12 DCM (telematics transceiver) connector.

(d) Turn the power switch on (ACC).

(e) Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.

*a

Component with harness connected

(Roof Console Box Sub-assembly)

(f) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

V14-8 (MCO+) - V14-7 (MCO-)

Tool setting

50 mV/DIV., 500 ms/DIV.

Vehicle condition

  1. Turn the power switch on (ACC).
  2. Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.

OK:

The waveform is similar to that shown in the illustration.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

NG

GO TO STEP 17

OK

16.

INSPECT DCM (TELEMATICS TRANSCEIVER) (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V14 roof console box sub-assembly connector.

(c) Connect the K140 DCM (telematics transceiver) connector.

(d) Turn the power switch on (ACC).

(e) Connect an oscilloscope to terminals 16 (MCO+) and 32 (MCO-) of the K140 DCM (telematics transceiver) connector.

*a

Component with harness connected

DCM (Telematics Transceiver)

(f) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

K140-16 (MCO+) - K140-32 (MCO-)

Tool setting

50 mV/DIV., 500 ms/DIV.

Vehicle condition

  1. Turn the power switch on (ACC).
  2. Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.

OK:

The waveform is similar to that shown in the illustration.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2020 MY Camry HV [09/2019 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE

NG

REPLACE DCM (TELEMATICS TRANSCEIVER) 2020 MY Camry HV [09/2019 - 10/2020]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

17.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V14-8 (MCO+) - B-3

Always

Below 1 Ω

V14-7 (MCO-) - B-2

Always

Below 1 Ω

V14-8 (MCO+) or B-3 - V14-15 (GND)

Always

10 kΩ or higher

V14-7 (MCO-) or B-2 - V14-15 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

18.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V14-6 (SNS2) - B-1

Always

Below 1 Ω

V14-7 (MCO-) - B-2

Always

Below 1 Ω

V14-6 (SNS2) or B-1 - V14-15 (GND)

Always

10 kΩ or higher

V14-7 (MCO-) or B-2 - V14-15 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

19.

CHECK MICROPHONE (OPERATION CHECK)

(a) Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click here 2020 MY Camry HV [09/2019 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: OPERATION CHECK

(b) When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.

Result

Proceed to

NG (w/o Manual (SOS) Switch)

A

NG (w/ Manual (SOS) Switch)

B

OK

C

B

GO TO STEP 26

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

A

20.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

(a) Disconnect the K2 radio and display receiver assembly connector.

(b) Disconnect the V18 roof console box sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-25 (SNS2) - V18-3 (SNS2)

Always

Below 1 Ω

K2-23 (MACC) - V18-6 (MACC)

Always

Below 1 Ω

K2-21 (MIN+) - V18-5 (MCO+)

Always

Below 1 Ω

K2-22 (MIN-) - V18-4 (MCO-)

Always

Below 1 Ω

K2-25 (SNS2) or V18-3 (SNS2) - Body ground

Always

10 kΩ or higher

K2-23 (MACC) or V18-6 (MACC) - Body ground

Always

10 kΩ or higher

K2-21 (MIN+) or V18-5 (MCO+) - Body ground

Always

10 kΩ or higher

K2-22 (MIN-) or V18-4 (MCO-) - Body ground

Always

10 kΩ or higher

K2-24 (SGND) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

21.

INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V18 roof console box sub-assembly connector.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K2-23 (MACC) - Body ground

Power switch on (ACC)

4 to 6 V

*a

Component with harness connected

(Radio and Display Receiver Assembly)

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-24 (SGND) - Body ground

Always

Below 1 Ω

K2-22 (MIN-) - Body ground

Always

Below 1 Ω

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

OK

22.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Connect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 (SNS2) - 4 (MCO-)

Always

Below 1 Ω

*a

Component without harness connected

(Roof Console Box Sub-assembly)

NG

GO TO STEP 25

OK

23.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V18 roof console box sub-assembly connector.

(c) Turn the power switch on (ACC).

(d) Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the V18 roof console box sub-assembly connector.

*a

Component with harness connected

(Roof Console Box Sub-assembly)

(e) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

V18-5 (MCO+) - V18-4 (MCO-)

Tool setting

50 mV/DIV., 500 ms/DIV.

Vehicle condition

  1. Turn the power switch on (ACC).
  2. Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.

OK:

The waveform is similar to that shown in the illustration.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2020 MY Camry HV [09/2019 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE

NG

24.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V18-5 (MCO+) - B-3

Always

Below 1 Ω

V18-4 (MCO-) - B-2

Always

Below 1 Ω

V18-5 (MCO+) or B-3 - V18-11 (GND)

Always

10 kΩ or higher

V18-4 (MCO-) or B-2 - V18-11 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

25.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V18-3 (SNS2) - B-1

Always

Below 1 Ω

V18-4 (MCO-) - B-2

Always

Below 1 Ω

V18-3 (SNS2) or B-1 - V18-11 (GND)

Always

10 kΩ or higher

V18-4 (MCO-) or B-2 - V18-11 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

26.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

(a) Disconnect the K2 radio and display receiver assembly connector.

(b) Disconnect the V18 roof console box sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-25 (SNS2) - V18-3 (SNS2)

Always

Below 1 Ω

K2-25 (SNS2) or V18-3 (SNS2) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

27.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))

(a) Disconnect the K2 radio and display receiver assembly connector.

(b) Disconnect the K140 DCM (telematics transceiver) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-21 (MIN+) - K140-16 (MCO+)

Always

Below 1 Ω

K2-22 (MIN-) - K140-32 (MCO-)

Always

Below 1 Ω

K2-21 (MIN+) or K140-16 (MCO+) - Body ground

Always

10 kΩ or higher

K2-22 (MIN-) or K140-32 (MCO-) - Body ground

Always

10 kΩ or higher

K2-24 (SGND) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

28.

CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY)

(a) Disconnect the K140 DCM (telematics transceiver) connector.

(b) Disconnect the V18 roof console box sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K140-5 (MCVD) - V18-6 (MACC)

Always

Below 1 Ω

K140-6 (MCI+) - V18-5 (MCO+)

Always

Below 1 Ω

K140-7 (MCI-) - V18-4 (MCO-)

Always

Below 1 Ω

K140-5 (MCVD) or V18-6 (MACC) - Body ground

Always

10 kΩ or higher

K140-6 (MCI+) or V18-5 (MCO+) - Body ground

Always

10 kΩ or higher

K140-7 (MCI-) or V18-4 (MCO-) - Body ground

Always

10 kΩ or higher

K140-23 (SGND) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

29.

INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Disconnect the K12 DCM (telematics transceiver) connector.

(b) Connect the K2 radio and display receiver assembly connector.

*a

Component with harness connected

(Radio and Display Receiver Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K2-24 (SGND) - Body ground

Always

Below 1 Ω

K2-22 (MIN-) - Body ground

Always

Below 1 Ω

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

OK

30.

INSPECT DCM (TELEMATICS TRANSCEIVER)

(a) Connect the K140 DCM (telematics transceiver) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K140-5 (MCVD) - Body ground

Power switch on (ACC)

4 to 6 V

*a

Component with harness connected

(DCM (Telematics Transceiver))

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K140-6 (MCI-) - Body ground

Always

Below 1 Ω

K140-23 (SGND) - Body ground

Always

Below 1 Ω

NG

REPLACE DCM (TELEMATICS TRANSCEIVER) 2020 MY Camry HV [09/2019 - 10/2020]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

OK

31.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Connect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 (SNS2) - 4 (MCO-)

Always

Below 1 Ω

*a

Component without harness connected

(Roof Console Box Sub-assembly)

NG

GO TO STEP 35

OK

32.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V18 roof console box sub-assembly connector.

(c) Turn the power switch on (ACC).

(d) Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the V18 roof console box sub-assembly connector.

*a

Component with harness connected

(Roof Console Box Sub-assembly)

(e) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

V18-5 (MCO+) - V18-4 (MCO-)

Tool setting

50 mV/DIV., 500 ms/DIV.

Vehicle condition

  1. Turn the power switch on (ACC).
  2. Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.

OK:

The waveform is similar to that shown in the illustration.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

NG

GO TO STEP 34

OK

33.

INSPECT DCM (TELEMATICS TRANSCEIVER) (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

(a) Connect the K2 radio and display receiver assembly connector.

(b) Connect the V18 roof console box sub-assembly connector.

(c) Connect the K140 DCM (telematics transceiver) connector.

(d) Turn the power switch on (ACC).

(e) Connect an oscilloscope to terminals 16 (MCO+) and 32 (MCO-) of the K140 DCM (telematics transceiver) connector.

*a

Component with harness connected

DCM (Telematics Transceiver)

(f) Check the signal waveform according to the condition(s) in the table below.

Item

Condition

Measurement terminal

K140-16 (MCO+) - K140-32 (MCO-)

Tool setting

50 mV/DIV., 500 ms/DIV.

Vehicle condition

  1. Turn the power switch on (ACC).
  2. Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.

OK:

The waveform is similar to that shown in the illustration.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2020 MY Camry HV [09/2019 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE

NG

REPLACE DCM (TELEMATICS TRANSCEIVER) 2020 MY Camry HV [09/2019 - 10/2020]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; CELLULAR COMMUNICATION: DCM(TELEMATICS TRANSCEIVER): REMOVAL

34.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V18-5 (MCO+) - B-3

Always

Below 1 Ω

V18-4 (MCO-) - B-2

Always

Below 1 Ω

V18-5 (MCO+) or B-3 - V18-11 (GND)

Always

10 kΩ or higher

V18-4 (MCO-) or B-2 - V18-11 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

35.

INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

(a) Remove the roof console box sub-assembly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): PERSONAL LIGHT: REMOVAL

(b) Disconnect the B telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

V18-3 (SNS2) - B-1

Always

Below 1 Ω

V18-4 (MCO-) - B-2

Always

Below 1 Ω

V18-3 (SNS2) or B-1 - V18-11 (GND)

Always

10 kΩ or higher

V18-4 (MCO-) or B-2 - V18-11 (GND)

Always

10 kΩ or higher

*a

Component without harness connected

(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))

*b

Component without harness connected

(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY