- DTC judgment completed
- System normal
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001KK6D |
| Model Year Start: 2020 | Model: Camry HV | Prod Date Range: [09/2019 - ] |
| Title: A25A-FXS (ENGINE CONTROL): SFI SYSTEM: P107A2A,P107A64; Fuel Rail Pressure Sensor (Low) Signal Stuck in Range; 2020 - 2024 MY Camry HV [09/2019 - ] | ||
|
DTC |
P107A2A |
Fuel Rail Pressure Sensor (Low) Signal Stuck in Range |
|
DTC |
P107A64 |
Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure |
DESCRIPTION
Refer to DTC P107A11.
Click here
![2020 - 2024 MY Camry HV [09/2019 - ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: P107A11; Fuel Rail Pressure Sensor (Low) Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P107A2A |
Fuel Rail Pressure Sensor (Low) Signal Stuck in Range |
When the target fuel pressure for the low pressure side changes, the change in the fuel pressure sensor (for low pressure side) value is abnormal (2 trip detection logic). |
|
Comes on |
DTC stored |
|
|
P107A64 |
Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure |
When the fuel pump on the low pressure side is operated at maximum speed when the engine is stopped at vehicle speed of 45 km/h (28 mph) or more, the low pressure side fuel pressure is higher or lower than threshold (2 trip detection logic). |
|
Comes on |
DTC stored |
|
MONITOR DESCRIPTION
Fuel Pressure Sensor Stuck Monitor
If the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) value does not follow the change in the target low pressure side fuel pressure, it is judged as a malfunction. If this malfunction is detected in 2 consecutive driving cycles, the ECM will illuminate the MIL and store DTC P107A2A.
Fuel Pressure Sensor Correlation Monitor
If the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) value is less than or higher than the threshold value when the fuel pump on the low pressure side is operated at maximum speed when the engine is stopped at vehicle speed of 45 km/h (28 mph) or more, it is judged as a malfunction has occurred. If this malfunction is detected for 2 consecutive driving cycles, the ECM will illuminate the MIL and store DTC P107A64.
MONITOR STRATEGY
|
Related DTCs |
P107B: Fuel pressure sensor rationality (stuck monitor) P107B: Fuel pressure sensor rationality (correlation monitor) |
|
Required Sensors/Components (Main) |
Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) |
|
Required Sensors/Components (Related) |
Atmospheric pressure sensor |
|
Frequency of Operation |
Continuous: Stuck monitor Once per driving cycle: Correlation monitor |
|
Duration |
Less than 30 seconds: Stuck monitor Less than 10 seconds: Correlation monitor |
|
MIL Operation |
2 driving cycles |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Stuck Monitor
|
All of the following conditions are met |
2 seconds or more |
|
Engine coolant temperature sensor malfunction (P0116, P0117, P0118) |
Not detected |
|
Intake air temperature sensor (mass air flow meter sub-assembly) malfunction (P0111, P0112, P0113) |
Not detected |
|
Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) circuit malfunction (P107C, P107D) |
Not detected |
|
Auxiliary battery voltage |
11 V or higher |
|
Fuel cut |
Off |
Correlation Monitor
|
All of the following conditions are met |
- |
|
Engine coolant temperature sensor malfunction (P0116, P0117, P0118) |
Not detected |
|
Intake air temperature sensor (mass air flow meter sub-assembly) malfunction (P0111, P0112, P0113) |
Not detected |
|
Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) circuit malfunction (P107C, P107D) |
Not detected |
|
Auxiliary battery voltage |
11 V or higher |
|
Engine coolant temperature |
75°C (167°F) or higher |
|
Intake air temperature |
-10°C (14°F) or higher |
|
Atmospheric pressure |
76 kPa(abs) [11 psi(abs)] or higher |
|
Fuel pump (for low pressure) operation at maximum duty |
1 second or more |
|
Engine shut off |
Executing |
|
Vehicle Speed |
45 km/h (28 mph) or more |
TYPICAL MALFUNCTION THRESHOLDS
Stuck Monitor
|
Malfunction counter |
3 times or more |
|
Malfunction counter is incremented when fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) output deviation |
Less than 12 kPa (0.1 kgf/cm2, 1.7 psi) |
Correlation Monitor
|
Malfunction counter |
2 seconds or more |
|
Malfunction counter is counted when following condition is met |
- |
|
Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) output |
Higher than 770 kPa (7.9 kgf/cm2, 112 psi), or less than 540 kPa (5.5 kgf/cm2, 78.3 psi) |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
P107A2A
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG).
- Turn the Techstream on.
-
Put the engine in Inspection Mode (Maintenance Mode).
Click here
- Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
- Turn the power switch off.
- Turn the power switch on (READY) [A].
- Turn the Techstream on.
-
Rev the engine for 15 seconds or more with the shift lever in P [B].
HINT:
During charge control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform steps [B] after charge control has completed.
-
Allow the engine to stop for 5 seconds or more [C].
HINT:
- If the engine does not stop, wait till the engine stops.
- If the engine coolant temperature is low, it may take some time for the engine to stop.
- Repeat [B] and [C] 5 times or more [D].
- Enter the following menus: Powertrain / Engine / Trouble Codes [E].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P107A2A.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [B] through [E] again.
-
[A] to [E]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
P107A64
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG).
- Turn the Techstream on.
-
Put the engine in Inspection Mode (Maintenance Mode).
Click here
- Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
- Turn the power switch off [A].
- Turn the power switch on (READY) [B].
-
Drive the vehicle at approximately 50 km/h (31 mph) for 15 seconds or more [C].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
- Enter the following menus: Powertrain / Engine / Trouble Codes [D].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P107A64.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [A] through [D] again.
-
[B] to [D]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
CAUTION / NOTICE / HINT
NOTICE:
-
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
for NICKEL METAL HYDRIDE BATTERY:
Click here
for LITHIUM-ION BATTERY:
Click here
(Select Powertrain in Health Check and then check the time stamp data.)
Click here
-
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
for NICKEL METAL HYDRIDE BATTERY:
Click here
for LITHIUM-ION BATTERY:
Click here
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P107A2A, P107A64, P008A00 OR P008B00) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs and record the Freeze Frame Data.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC P107A2A is output |
A |
|
DTC P107A64 is output |
B |
|
DTC P107A2A or P107A64 and P008A00 are output |
C |
|
DTC P107A2A or P107A64 and P008B00 are output |
D |
|
DTC P107A2A, P107A64, P008A00 and/or P008B00 and other DTCs are output |
E |
HINT:
If any DTCs other than P107A2A, P107A64, P008A00 and/or P008B00 are output, troubleshoot those DTCs first.
| B |
|
| C |
|
| D |
|
| E |
|
GO TO DTC CHART
|
|
|
2. |
READ VALUE USING TECHSTREAM (FUEL PRESSURE (LOW)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(g) Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
(h) Turn the power switch off.
(i) Discharge the fuel pressure.
HINT:
DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream.
(1) Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
(2) Turn the power switch on (IG).
(3) Turn the Techstream on.
(4) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(5) Start the engine.
(6) After the engine has stopped on its own, turn the power switch off.
HINT:
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
(7) Turn the power switch on (IG).
(8) Turn the Techstream on.
(9) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(10) Crank the engine again and make sure that the engine does not start.
(11) Install the EFI-MAIN NO. 2 fuse.
(j) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(k) Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the Techstream.
|
Result |
Proceed to |
|---|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 value drops |
A |
|
Fuel Pressure (Low) / Fuel Pressure 2 value does not fluctuate |
B |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click here
| B |
|
REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)
|
|
|
3. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the power switch off and wait for at least 30 seconds.
|
|
4. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P107A2A OR P107A64) |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > Utility
|
Tester Display |
|---|
|
All Readiness |
(c) Input the DTC: P107A2A or P107A64.
(d) Check the DTC judgment result.
|
Result |
Proceed to |
|---|---|
|
NORMAL (DTCs are not output) |
A |
|
ABNORMAL (DTC P107A2A or P107A64 is output) |
B |
| A |
|
|
|
5. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Install the fuel pressure gauge (for low pressure line of low pressure side).
Click here
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Fuel Pump Duty Ratio (Brushless) |
|
Data List Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(f) Compare the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed.
Standard:
|
Techstream Operation |
Standard |
|---|---|
|
Low |
Data List value and fuel pressure gauge are within +/-50 kPa of each other |
|
High |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click here
| OK |
|
REPLACE ECM
|
| NG |
|
REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)
|
|
6. |
READ FREEZE FRAME DATA (FUEL PRESSURE (LOW) / FUEL PRESSURE 2) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Read the Freeze Frame Data value from step 1.
Powertrain > Engine > DTC(P107A2A) > Freeze Frame Data
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
|
Result |
Proceed to |
|---|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 value is 770 kPag or higher |
A |
|
Fuel Pressure (Low) / Fuel Pressure 2 value is 540 kPag or less |
B |
| A |
|
| B |
|
|
7. |
CHECK FUEL LEAK |
(a) Check around and beneath the vehicle for fuel leaks, fumes, etc.
OK:
No fuel leaks present.
| NG |
|
REPAIR OR REPLACE FUEL LEAK POINT |
|
|
8. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless)
Powertrain > Engine > Active Test
|
Tester Display |
|---|
|
Control the Fuel Pump Duty Ratio (Brushless) |
(e) Check whether the fuel pump operating sound occurs when performing the Active Test on the Techstream.
Standard:
|
Techstream Operation |
Standard |
|---|---|
|
High |
Operating sounds can be heard from fuel pump (for low pressure side) |
HINT:
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click here
| NG |
|
REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
|
|
|
9. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Discharge the fuel pressure.
HINT:
DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream.
(1) Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
(2) Connect the Techstream to the DLC3.
(3) Turn the power switch on (IG).
(4) Turn the Techstream on.
(5) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(6) Start the engine.
(7) After the engine has stopped on its own, turn the power switch off.
HINT:
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
(8) Turn the power switch on (IG).
(9) Turn the Techstream on.
(10) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(11) Crank the engine again and make sure that the engine does not start.
(12) Install the EFI-MAIN NO. 2 fuse.
(b) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Fuel Pump Duty Ratio |
|
Data List Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(c) Read the value displayed on the Techstream when the Active Test was performed.
Standard:
|
Techstream Operation |
Standard |
|---|---|
|
Low to High |
When switching from Low to High, Fuel Pressure (Low) / Fuel Pressure 2 value changes |
HINT:
Once the fuel pressure becomes high, the fuel pressure will not decrease, even when switched from High to Low. Therefore, make sure that the fuel pressure is low before checking that the fuel pressure changes when switching from Low to High.
| NG |
|
|
|
10. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Discharge the fuel pressure.
HINT:
DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream.
(1) Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
(2) Connect the Techstream to the DLC3.
(3) Turn the power switch on (IG).
(4) Turn the Techstream on.
(5) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(6) Start the engine.
(7) After the engine has stopped on its own, turn the power switch off.
HINT:
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
(8) Turn the power switch on (IG).
(9) Turn the Techstream on.
(10) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(11) Crank the engine again and make sure that the engine does not start.
(12) Install the EFI-MAIN NO. 2 fuse.
(b) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Fuel Pump Duty Ratio (Brushless) |
|
Data List Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(c) Read the value displayed on the Techstream when the Active Test was performed.
Standard:
|
Techstream Operation |
Fuel Pressure (Low) / Fuel Pressure 2 |
|---|---|
|
Low |
50 kPag or higher |
|
High |
420 kPag or higher |
HINT:
Once the fuel pressure becomes high, the fuel pressure will not decrease, even when switched from High to Low. Therefore, make sure that the fuel pressure is low before checking that the fuel pressure changes when switching from Low to High.
OK:
Actual Low and High values are as shown above.
| NG |
|
|
|
11. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Install the fuel pressure gauge (for low pressure line of low pressure side).
Click here
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Fuel Pump Duty Ratio (Brushless) |
|
Data List Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(f) Compare the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed.
Standard:
|
Techstream Operation |
Standard |
|---|---|
|
Low |
Data List value and fuel pressure gauge are within +/-50 kPa of each other |
|
High |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click here
| NG |
|
REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)
|
|
|
12. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the power switch off and wait for at least 30 seconds.
|
|
13. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P107A2A OR P107A64) |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > Utility
|
Tester Display |
|---|
|
All Readiness |
(c) Input the DTC: P107A2A or P107A64.
(d) Check the DTC judgment result.
|
Result |
Proceed to |
|---|---|
|
NORMAL (DTCs are not output) |
A |
|
ABNORMAL (DTC P107A2A or P107A64 is output) |
B |
| A |
|
| B |
|
REPLACE ECM
|
|
14. |
READ VALUE USING TECHSTREAM (FUEL PRESSURE (LOW)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(g) Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
(h) Turn the power switch off.
(i) Wait for 10 seconds.
(j) Turn the power switch on (IG).
(k) Turn the Techstream on.
(l) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(m) Compare the Fuel Pressure (Low) value recorded with the engine running to the Fuel Pressure (Low) value currently shown on the Techstream.
|
Result |
Proceed to |
|---|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 value is maintained |
A |
|
Fuel Pressure (Low) / Fuel Pressure 2 value drops |
B |
HINT:
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click here
| A |
|
REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
|
| B |
|
REPLACE FUEL MAIN VALVE ASSEMBLY (FOR HIGH PRESSURE)
|
|
15. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Install the fuel pressure gauge (for low pressure line of low pressure side).
Click here
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Fuel Pump Duty Ratio (Brushless) |
|
Data List Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(f) Read the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed.
|
Techstream Operation |
Result |
Proceed to |
|---|---|---|
|
Low to High |
Data List value does not change, but fuel pressure gauge changes |
A |
|
Data List value and fuel pressure gauge do not change |
B |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click here
| A |
|
REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)
|
| B |
|
REPLACE FUEL PUMP CONTROL ECU
|
|
16. |
READ VALUE USING TECHSTREAM (FUEL PRESSURE (LOW)) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(g) Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
(h) Turn the power switch off.
(i) Discharge the fuel pressure.
HINT:
DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream.
(1) Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
(2) Turn the power switch on (IG).
(3) Turn the Techstream on.
(4) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(5) Start the engine.
(6) After the engine has stopped on its own, turn the power switch off.
HINT:
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
(7) Turn the power switch on (IG).
(8) Turn the Techstream on.
(9) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility
|
Tester Display |
|---|
|
Inspection Mode |
(10) Crank the engine again and make sure that the engine does not start.
(11) Install the EFI-MAIN NO. 2 fuse.
(j) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(k) Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the Techstream.
|
Result |
Proceed to |
|---|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 value drops |
A |
|
Fuel Pressure (Low) / Fuel Pressure 2 value is maintained |
B |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click here
| B |
|
REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)
|
|
|
17. |
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY RATIO (BRUSHLESS)) |
(a) Install the fuel pressure gauge (for low pressure line of low pressure side).
Click here
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
Powertrain > Engine > Active Test
|
Active Test Display |
|---|
|
Control the Fuel Pump Duty Ratio (Brushless) |
|
Data List Display |
|---|
|
Fuel Pressure (Low) / Fuel Pressure 2 |
(f) Compare the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed.
Standard:
|
Techstream Operation |
Standard |
|---|---|
|
Low |
Data List value and fuel pressure gauge are within +/-50 kPa of each other |
|
High |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click here
| NG |
|
REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)
|
|
|
18. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the power switch off and wait for at least 30 seconds.
|
|
19. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P107A2A OR P107A64) |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > Utility
|
Tester Display |
|---|
|
All Readiness |
(c) Input the DTC: P107A2A or P107A64.
(d) Check the DTC judgment result.
|
Result |
Proceed to |
|---|---|
|
NORMAL (DTCs are not output) |
A |
|
ABNORMAL (DTC P107A2A or P107A64 is output) |
B |
| A |
|
| B |
|
REPLACE ECM
|
|
|