Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001JT6R
Model Year Start: 2019 Model: Camry HV Prod Date Range: [09/2018 - 09/2019]
Title: DOOR / HATCH: FRONT DOOR: DISASSEMBLY; 2019 MY Camry HV [09/2018 - 09/2019]

DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Door window regulator sub-assembly
  • Door glass
  • Door glass run

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry HV [07/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Click here 2019 MY Camry HV [09/2018 - 09/2019]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here 2019 MY Camry HV [09/2018 - 09/2019]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

(a) Disengage the clip and guide to remove the front door lower frame bracket garnish.

5. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

(a) Using a moulding remover, disengage the 3 claws to remove the front door armrest cover sub-assembly.

6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

(a) Apply protective tape to the front door trim board sub-assembly as shown in the illustration.

Protective Tape

(b) Disengage the 3 clips, 15 claws and 8 guides as shown in the illustration.

Place Hand Here

Remove in this Direction

Order of Removal

(c) Disengage the guide as shown in the illustration.

Remove in this Direction

(d) Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.

7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

(a) Apply protective tape to the front door trim board sub-assembly as shown in the illustration.

Protective Tape

(b) Disengage the 3 clips, 15 claws and 8 guides as shown in the illustration.

Place Hand Here

Remove in this Direction

Order of Removal

(c) Disengage the guide as shown in the illustration.

Remove in this Direction

(d) Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.

8. REMOVE FRONT ARMREST ASSEMBLY

(a) Disengage the guide to remove the front armrest assembly as shown in the illustration.

Remove in this Direction

9. REMOVE COURTESY LIGHT ASSEMBLY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): DOOR COURTESY LIGHT: REMOVAL+

10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

(a) Apply protective tape to the front door panel as shown in the illustration.

Protective Tape

(b) Remove the 3 screws.

(c) Disengage the 10 clips as shown in the illustration.

Place Hand Here

Remove in this Direction

(d) Disengage the 7 claws and guide as shown in the illustration.

Remove in this Direction

(e) Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly as shown in the illustration.

*1

Front Door Inside Locking Cable Assembly

*2

Front Door Lock Remote Control Cable Assembly

Remove in this Direction

11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

(a) Disengage the clip.

(b) Remove the front door inner glass weatherstrip with front door vent seal as shown in the illustration.

Remove in this Direction

12. REMOVE FRONT DOOR VENT SEAL

(a) Remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.

Remove in this Direction

13. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

(a) Disengage the 3 claws to remove the front door inside handle sub-assembly.

14. REMOVE HOLE PLUG

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; MIRROR (EXT): OUTER REAR VIEW MIRROR: REMOVAL+

15. REMOVE OUTER MIRROR INSTALL HOLE COVER

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; MIRROR (EXT): OUTER REAR VIEW MIRROR: REMOVAL+

16. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; MIRROR (EXT): OUTER REAR VIEW MIRROR: REMOVAL+

17. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; AUDIO / VIDEO: FRONT DOOR SPEAKER: REMOVAL+

18. REMOVE FRONT DOOR SERVICE HOLE COVER

(a) Disengage the 2 clamps.

(b) Turn each front door weatherstrip clip 45 degrees and remove the 4 front door weatherstrip clips as shown in the illustration.

(c) Disengage the 3 clips to remove the front door service hole cover.

19. REMOVE DOOR SIDE AIRBAG SENSOR

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL+

20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

(a) Remove the hole plug.

(b) for Driver Side:

(1) Connect the multiplex network master switch assembly.

(c) for Front Passenger Side:

(1) Connect the power window regulator switch assembly.

(d) Connect the cable to the negative (-) auxiliary battery terminal.

(e) Turn the power switch on (IG).

(f) Move the front door glass sub-assembly so that the door glass bolts can be seen.

(g) Turn the power switch off.

(h) Disconnect the cable from the negative (-) auxiliary battery terminal.

(i) for Driver Side:

(1) Disconnect the multiplex network master switch assembly.

(j) for Front Passenger Side:

(1) Disconnect the power window regulator switch assembly.

(k) Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly to fall.

(l) Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

Remove in this Direction (1)

Remove in this Direction (2)

NOTICE:

Do not damage the front door glass sub-assembly.

21. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

(a) Disengage the 2 claws to remove the front door No. 2 service hole cover.

(b) Disconnect the connector.

*a

Temporary Bolt

(c) Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

(d) Remove the 5 bolts.

(e) Remove the front door window regulator assembly.

(f) Remove the temporary bolt from the front door window regulator assembly.

22. REMOVE FRONT DOOR PANEL PROTECTOR

(a) Remove the front door panel protector.

23. REMOVE FRONT DOOR GLASS RUN

(a) Remove the front door glass run.

24. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

(a) Remove the 2 bolts.

Remove in this Direction

(b) Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.

25. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

(a) Disengage the 2 claws.

(b) Using a screwdriver, disconnect the connector.

(c) Disengage the 3 clamps.

(d) Disengage the 2 claws and move the lever as shown in the illustration.

Disengage in this Direction

(e) Remove the front door outside handle assembly as shown in the illustration.

Remove in this Direction

26. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

(a) Remove the hole plug.

(b) Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.

27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

(a) Remove the hole plug.

(b) Using a T30 "TORX" socket wrench, loosen the screw.

(c) Disengage the 2 guides and claw and remove the front door outside handle cover.

28. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

(a) Disengage the 3 claws to remove the front door front outside handle pad.

29. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

(a) Disengage the 3 guides and claw to remove the front door rear outside handle pad.

30. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; DOOR LOCK: FRONT DOOR LOCK: REMOVAL+

31. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

(a) Using a T30 "TORX" socket wrench, remove the screw.

*A

Inside

*B

Outside

(b) Slide the front door outside handle frame sub-assembly as shown in the illustration to disengage the claw and then remove the front door outside handle frame sub-assembly.

32. REMOVE FRONT DOOR LOCK OPEN ROD

(a) Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.

Remove in this Direction (1)

Remove in this Direction (2)

33. REMOVE FRONT DOOR CHECK ASSEMBLY

(a) Remove the 2 nuts, bolt and front door check assembly.

Nut

Bolt

34. REMOVE FRONT DOOR WEATHERSTRIP

(a) Using a clip remover, disengage the 25 clips and remove the front door weatherstrip.

35. REMOVE DOOR FRAME GARNISH

(a) Disengage the 3 claws to remove the door frame garnish.

36. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

(a) Remove the 2 bolts.

Remove in this Direction

(b) Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.

37. REMOVE FRONT DOOR PANEL CUSHION

(a) Disengage the 2 claws to remove the front door panel cushion.

38. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP

(a) Disengage the 8 clips to remove the front door No. 2 weatherstrip.

39. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL+

40. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; EXTERIOR PANELS / TRIM: FRONT PILLAR UPPER COVER: REMOVAL+

41. REMOVE DOOR WINDOW FRAME MOULDING CLIP

(a) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.

*a

Protective Tape

Remove in this Direction

42. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; EXTERIOR PANELS / TRIM: FRONT DOOR WINDOW FRAME MOULDING: REMOVAL+

43. REMOVE FRONT DOOR REAR OUTSIDE SEAL

(a) Disengage the guide to remove the front door rear outside seal.

44. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; EXTERIOR PANELS / TRIM: FRONT DOOR WINDOW FRAME MOULDING: REMOVAL+