Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001ETPV
Model Year Start: 2019 Model: Camry HV Prod Date Range: [09/2018 - 10/2020]
Title: PRE-COLLISION: PRE-COLLISION SYSTEM: C1A69; Brake Control Signal Mismatch; 2019 - 2020 MY Camry HV [09/2018 - 10/2020]

DTC

C1A69

Brake Control Signal Mismatch

DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) sends signals to the millimeter wave radar sensor assembly according to the brake control status. If the millimeter wave radar sensor assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly), it will store DTC C1A69.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1A69

Brake Control Signal Mismatch

While the power switch is on (IG), the millimeter wave radar sensor assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for 1 second or more.
  • Electronically controlled brake system
  • Millimeter wave radar sensor assembly

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: ADJUSTMENT

  • The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

PROCEDURE

1.

CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

HINT:

Pre-collision system DTC C1A69 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.

(a) Check for DTCs.

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

Electronically controlled brake system DTCs are not output

A

Electronically controlled brake system DTCs are output

B
B

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM

A

2.

CHECK FOR DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

  1. Turn the power switch on (IG) and wait 1 second or more.

(c) Check for DTCs.

Body Electrical > Pre-Collision 2 > Trouble Codes

Result

Proceed to

DTC C1A69 is not output

A

DTC C1A69 is output

B
A

USE SIMULATION METHOD TO CHECK 2019 MY Camry HV [09/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry HV [09/2019 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY