| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001E84M |
| Model Year Start: 2019 | Model: Camry HV | Prod Date Range: [09/2018 - ] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: C14B3; Reaction Force Pressure Sensor Zero Point Malfunction; 2019 - 2024 MY Camry HV [09/2018 - ] | ||
|
DTC |
C14B3 |
Reaction Force Pressure Sensor Zero Point Malfunction |
DESCRIPTION
The reaction force pressure sensor detects and outputs the brake fluid pressure of the stroke simulator, which changes in accordance with brake pedal operation, to the skid control ECU (brake booster with master cylinder assembly).
|
DTC No. |
Detection Item |
INF Code |
DTC Detection Condition |
Trouble Area |
MIL |
Note |
|---|---|---|---|---|---|---|
|
C14B3 |
Reaction Force Pressure Sensor Zero Point Malfunction |
204 |
When the brake pedal is not depressed, the reaction force pressure sensor output value is -0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or less or 1.53 MPa (15.6 kgf/cm2, 222 psi) or more for 3 seconds or more. |
Skid control ECU (brake booster with master cylinder assembly) |
Comes on |
|
MONITOR DESCRIPTION
When the brake pedal is not operated and the value of the reaction force pressure sensor exceeds a specific value, or the value is less than a specific value for a certain amount of time, the skid control ECU (brake booster with master cylinder assembly) judges that the zero point of the reaction force pressure sensor is abnormal and illuminates the MIL and stores this DTC.
MONITOR STRATEGY
|
Related DTCs |
C14B3: Reaction force pressure sensor exceeded learning limit |
|
Required Sensors/Components(Main) |
Brake actuator (brake booster with master cylinder assembly) |
|
Required Sensors/Components(Related) |
Brake pedal stroke sensor assembly Brake actuator (brake booster with master cylinder assembly) Stop light switch assembly |
|
Frequency of Operation |
Continuous |
|
Duration |
3 seconds |
|
MIL Operation |
Immediately |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
C0562 (Brake pedal stroke sensor assembly voltage circuit/open) C124B (Brake pedal stroke sensor assembly invalid data) C14B0 (Reaction force pressure sensor voltage circuit check) C14B1 (Reaction force pressure sensor lost communication) C14B2 (Reaction force pressure sensor internal malfunction) C14B4 (Reaction force pressure sensor intermittent/erratic) C14B5 (Reaction force pressure sensor invalid data) P057C, P05DD (Brake pedal stroke sensor assembly open circuit) P057D, P05DE (Brake pedal stroke sensor assembly circuit high) P057E, P05DF (Brake pedal stroke sensor assembly intermittent/erratic) P05E0 (Brake pedal stroke sensor assembly "1"/"2" correlation) |
|
All of the following conditions are met |
- |
|
Brake pedal stroke sensor assembly circuit fail |
Not detected |
|
Reaction force pressure sensor circuit fail |
Not detected |
|
Brake |
Off |
TYPICAL MALFUNCTION THRESHOLDS
|
Reaction force pressure sensor |
Less than -0.63 MPa (-6.4 kgf/cm2, -91.4 psi), or higher than 1.53 MPa (15.6 kgf/cm2, 222 psi) |
COMPONENT OPERATING RANGE
|
All of the following conditions are met |
- |
|
Brake pedal stroke sensor assembly circuit fail |
Not detected |
|
Reaction force pressure sensor circuit fail |
Not detected |
|
Brake |
Off |
|
Reaction force pressure sensor |
-0.63 MPa (-6.4 kgf/cm2, -91.4 psi) or more, and 1.53 MPa (15.6 kgf/cm2, 222 psi) or less |
CONFIRMATION DRIVING PATTERN
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Wait 3 seconds.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
-
Read the DTCs.
HINT:
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.
-
If the DTCs are not output, perform a universal trip and check for permanent DTCs.
Click here
![2019 - 2024 MY Camry HV [09/2018 - ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTCs are output, the system is normal.
CAUTION / NOTICE / HINT
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here
PROCEDURE
|
1. |
CHECK BRAKE PEDAL |
(a) Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
(b) Check and adjust the brake pedal height.
Click here
(c) Adjust the brake pedal stroke sensor assembly.
Click here
|
|
2. |
READ VALUE USING TECHSTREAM (REACTION FORCE PRESSURE) |
(a) Select the Data List on the Techstream.
Chassis > ABS/VSC/TRAC > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Reaction Force Pressure |
Pressure value of stroke simulator |
Min.: 0.00 MPa, Max.: 24.48 MPa |
Brake pedal released: 0.00 MPa |
Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
Chassis > ABS/VSC/TRAC > Data List
|
Tester Display |
|---|
|
Reaction Force Pressure |
(b) Check that the reaction force pressure sensor output value is within 0.00 to 1.53 MPa when the brake pedal is not depressed.
OK:
The reaction force pressure sensor output value is within 0.00 to 1.53 MPa.
HINT:
If the reaction force pressure sensor output value is within 0.00 to 1.53 MPa, the skid control ECU (brake booster with master cylinder assembly) automatically performs zero point calibration every time the power switch is turned on (IG).
Therefore, if the reaction force pressure sensor output value is not within 0.00 to 1.53 MPa, replace the skid control ECU (brake booster with master cylinder assembly) with a new one.
| NG |
|
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
|
|
|
3. |
RECONFIRM DTC |
(a) Clear the DTCs.
Chassis > ABS/VSC/TRAC > Clear DTCs
(b) Turn the power switch off.
(c) Turn the power switch on (IG).
(d) Check if the same DTC is output.
Chassis > ABS/VSC/TRAC > Trouble Codes
HINT:
Even if the DTC is cleared, it will immediately be output again if the reaction force pressure sensor zero point malfunction remains.
|
Result |
Proceed to |
|---|---|
|
DTC C14B3 is not output. |
A |
|
DTC C14B3 is output. |
B |
| A |
|
USE SIMULATION METHOD TO CHECK
|
| B |
|
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
|
|
|