Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000164IO
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: A25A-FXS (INTAKE / EXHAUST): EXHAUST MANIFOLD: INSTALLATION; 2018 - 2024 MY Camry HV [07/2017 -        ]

INSTALLATION

PROCEDURE

1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

(a) Type A:

(1) Install the No. 2 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 6 bolts.

Torque:

11 N·m {112 kgf·cm, 8 ft·lbf}

(b) Type B:

(1) Install the No. 2 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 3 bolts.

Torque:

11 N·m {112 kgf·cm, 8 ft·lbf}

2. INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

(a) Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.

(b) Temporarily install the exhaust manifold (TWC: Front Catalyst), No. 1 exhaust manifold heat insulator and No. 1 upper front floor heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.

(c) Using a 12 mm deep socket wrench, temporarily install the exhaust manifold (TWC: Front Catalyst) to the cylinder head sub-assembly with 7 new nuts.

(d) Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:

26 N·m {265 kgf·cm, 19 ft·lbf}

3. INSTALL MANIFOLD STAY

(a) Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.

(b) Tighten the bolt and nut in the order shown in the illustration.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

4. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

(a) Type A:

(1) Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 5 bolts.

Torque:

Specified tightening torque :

10 N·m {102 kgf·cm, 7 ft·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)

*a

Torque Wrench Fulcrum Length

(b) Type B:

(1) Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 3 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

5. INSTALL NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

(a) Using a 10 mm union nut wrench, install the No. 1 upper front floor heat insulator to the vehicle body with the 2 nuts.

Torque:

Specified tightening torque :

4.9 N·m {50 kgf·cm, 43 in·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 4.3 N*m (44 kgf*cm, 38 in.*lbf)

*a

Torque Wrench Fulcrum Length

6. INSTALL WIRE HARNESS CLAMP BRACKET

(a) Install the wire harness clamp bracket with the bolt.

Torque:

13 N·m {133 kgf·cm, 10 ft·lbf}

7. INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (ENGINE CONTROL): AIR FUEL RATIO SENSOR (for Sensor 1): INSTALLATION

8. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER: INSTALLATION+ 2020 - 2024 MY Camry HV [09/2019 -        ]; BRAKE SYSTEM (OTHER): BRAKE BOOSTER: INSTALLATION+

9. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; WIPER / WASHER: FRONT WIPER MOTOR: INSTALLATION

10. INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; P710 (HYBRID TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE: INSTALLATION+

11. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

(a) Install 2 new gaskets to the front exhaust pipe assembly (TWC: Rear Catalyst).

(b) Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.

(c) Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) and center exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

(d) Engage the wire harness clamp.

(e) Connect the air fuel ratio sensor (for sensor 2) connector.

12. INSTALL CENTER FLOOR CROSSMEMBER BRACE

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (INTAKE / EXHAUST): EXHAUST PIPE: INSTALLATION+

13. INSTALL FRONT CENTER FLOOR BRACE

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (INTAKE / EXHAUST): EXHAUST PIPE: INSTALLATION+

14. INSTALL FRONT FLOOR COVER LH

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (INTAKE / EXHAUST): EXHAUST PIPE: INSTALLATION+

15. INSTALL FRONT FLOOR COVER RH

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (INTAKE / EXHAUST): EXHAUST PIPE: INSTALLATION+

16. INSPECT FOR EXHAUST GAS LEAK

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (INTAKE / EXHAUST): EXHAUST PIPE: INSTALLATION+

17. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here 2018 MY Camry HV [07/2017 - 09/2018]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2019 - 2020 MY Camry HV [09/2018 - 10/2020]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+

18. INSTALL NO. 1 ENGINE UNDER COVER

Click here 2018 MY Camry HV [07/2017 - 09/2018]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2019 - 2020 MY Camry HV [09/2018 - 10/2020]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+

19. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Click here 2018 MY Camry HV [07/2017 - 09/2018]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2019 - 2020 MY Camry HV [09/2018 - 10/2020]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+

20. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Click here 2018 MY Camry HV [07/2017 - 09/2018]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2019 - 2020 MY Camry HV [09/2018 - 10/2020]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+ 2021 - 2024 MY Camry HV [10/2020 -        ]; A25A-FXS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION+