- Replacement of air fuel ratio sensor
- Gas leak from exhaust system is repaired
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000164IN |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - ] |
| Title: A25A-FXS (INTAKE / EXHAUST): EXHAUST MANIFOLD: REMOVAL; 2018 - 2024 MY Camry HV [07/2017 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold (TWC: Front Catalyst) removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
|
Inspection After Repair |
|
|
CAUTION:
-
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
-
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
PROCEDURE
1. REMOVE FRONT FLOOR COVER LH
Click here
![2018 - 2024 MY Camry HV [07/2017 - ]; A25A-FXS (INTAKE / EXHAUST): EXHAUST PIPE: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT FLOOR COVER RH
Click here
3. REMOVE FRONT CENTER FLOOR BRACE
Click here
4. REMOVE CENTER FLOOR CROSSMEMBER BRACE
Click here
5. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
CAUTION:
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
|
(a) Disengage the wire harness clamp. |
|
(b) Disconnect the air fuel ratio sensor (for sensor 2) connector.
|
(c) Remove the 2 bolts, 2 nuts and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst) and center exhaust pipe assembly. |
|
(d) Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.
(e) Remove the 2 gaskets from the front exhaust pipe assembly (TWC: Rear Catalyst).
6. REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR
Click here
7. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Click here
8. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here
9. REMOVE NO. 1 ENGINE UNDER COVER
Click here
10. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
Click here
11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Click here
12. REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Click here
13. REMOVE AIR FUEL RATIO SENSOR (for Sensor 1)
Click here
14. REMOVE WIRE HARNESS CLAMP BRACKET
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
|
(a) Remove the bolt and wire harness clamp bracket. |
|
15. SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
(a) Type A:
|
(1) Remove the 5 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst). |
|
(b) Type B:
|
(1) Remove the 3 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst). |
|
16. SEPARATE NO. 1 UPPER FRONT FLOOR HEAT INSULATOR
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
|
(a) Remove the 2 nuts and separate the No. 1 upper front floor heat insulator from the vehicle body. |
|
17. REMOVE MANIFOLD STAY
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
|
(a) Remove the bolt, nut and manifold stay from the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly. |
|
18. REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)
CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
|
(a) Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly. |
|
(b) Remove the No. 1 upper front floor heat insulator, No. 1 exhaust manifold heat insulator and exhaust manifold (TWC: Front Catalyst).
|
(c) Remove the exhaust manifold to head gasket from the cylinder head sub-assembly. |
|
19. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
(a) Type A:
|
(1) Remove the 6 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst). |
|
(b) Type B:
|
(1) Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst). |
|
|
|