INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here

PROCEDURE

1. INSTALL EGR VALVE ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click here

(a) Using an 8 mm socket wrench, install the EGR valve assembly to the EGR valve bracket with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing.

*a Pin *b Hole

(c) Using the 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(d) for EGR Valve Bracket Connection Type:

(1) Using the 8 mm socket wrench, connect the fuel pipe sub-assembly to the EGR valve bracket with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(e) w/ Water Hose Connector:

*a	Retainer
	Push in

(1) Align the water hose connector with the EGR valve assembly, push the No. 4 water by-pass hose onto the EGR valve assembly, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.

(2) Check that the EGR valve assembly and No. 4 water by-pass hose are securely connected by pulling on them.

(f) w/o Water Hose Connector:

(1) Connect the No. 4 water by-pass hose to the EGR valve assembly and slide the clip to secure it.

(g) Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.

2. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

(a) Install a new EGR inlet gasket to the intake manifold.

(b) Install a new EGR valve adapter gasket to the No. 1 EGR pipe sub-assembly.

(c) Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly to the intake manifold and EGR valve assembly with the 4 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

3. CONNECT EGR COOLER ASSEMBLY

(a) Install a new EGR valve gasket to the EGR valve assembly. NOTICE: Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.

*a Claw

(b) Connect the EGR cooler assembly to the EGR valve assembly with the 2 bolts.

Torque:

24 N·m {245 kgf·cm, 18 ft·lbf}

4. CONNECT ENGINE WIRE

(a) Engage the 2 wire harness clamps to connect the engine wire.

(b) Install the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(c) Connect the EGR valve assembly connector.

(d) Engage the 3 hose clamps to connect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.

*1 No. 1 Fuel Vapor Feed Hose *2 No. 2 Fuel Vapor Feed Hose

5. ADD ENGINE COOLANT

Click here

6. INSPECT FOR COOLANT LEAK (for Engine)

Click here

7. INSPECT FOR EXHAUST GAS LEAK (for Engine)

Click here

8. PERFORM INITIALIZATION

(a) Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click here