Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000163YZ
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 10/2020]
Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: C1626; Steering Angle Sensor Failure; 2018 - 2020 MY Camry HV [07/2017 - 10/2020]

DTC

C1626

Steering Angle Sensor Failure

DESCRIPTION

  • This DTC is stored if the television camera controller receives a signal via CAN communication from the steering sensor that indicates an internal malfunction.
  • This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates an internal malfunction.

Television Camera Controller

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

C1626

Steering Angle Sensor Failure

A fail flag is transmitted from the steering angle sensor
  • Steering sensor
  • Television camera controller

Panoramic View Monitor

Rear Television Camera Assembly

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

C1626

Steering Angle Sensor Failure

A fail flag is transmitted from the steering angle sensor
  • Steering sensor
  • Rear television camera assembly

Parking Assist Camera

CAUTION / NOTICE / HINT

NOTICE:

  • When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: CALIBRATION

  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

PROCEDURE

1.

CHECK DTC OUTPUT

(a) Clear the DTCs.

Chassis > Panoramic View Monitor > Clear DTCs

Chassis > Parking Assist Camera > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Chassis > Panoramic View Monitor > Trouble Codes

Chassis > Parking Assist Camera > Trouble Codes

Result

Proceed to

DTC C1626 is output

A

DTC C1626 is not output

B
B

USE SIMULATION METHOD TO CHECK 2018 MY Camry HV [07/2017 - 09/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry HV [09/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry HV [09/2019 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

A

2.

REPLACE STEERING SENSOR

(a) Replace the steering sensor with a normally functioning one.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL

NEXT

3.

CHECK DTC OUTPUT

(a) Clear the DTCs.

Chassis > Panoramic View Monitor > Clear DTCs

Chassis > Parking Assist Camera > Clear DTCs

(b) Check for DTCs.

Chassis > Panoramic View Monitor > Trouble Codes

Chassis > Parking Assist Camera > Trouble Codes

Result

Proceed to

No DTCs are output

A

DTC C1626 is output ("Panoramic View Monitor")

B

DTC C1626 is output ("Parking Assist Camera")

C
A

END (STEERING SENSOR WAS DEFECTIVE)
B

REPLACE TELEVISION CAMERA CONTROLLER

C

REPLACE REAR TELEVISION CAMERA ASSEMBLY