| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000163YD |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - 10/2020] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: DATA LIST / ACTIVE TEST; 2018 - 2020 MY Camry HV [07/2017 - 10/2020] | ||
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (READY).
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Panoramic View Monitor or Parking Assist Camera / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > Panoramic View Monitor > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
RHD/LHD Data Check |
Status of the RHD/LHD data check |
Normal/Abnormal |
Normal: Television camera controller is normal Abnormal: Television camera controller is abnormal |
- |
|
HV/ENG Data Check |
Status of the HV/ENG data check |
Normal/Abnormal |
Normal: Television camera controller is normal Abnormal: Television camera controller is abnormal |
- |
|
2WD/4WD Data Check |
Status of the 2WD/AWD data check |
Normal/Abnormal |
Normal: Television camera controller ECU is normal Abnormal: Television camera controller is abnormal |
- |
|
Main CPU Forced Termination Detection Record |
A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the power switch off and a forced end was applied |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Main CPU Abnormal Response Record |
A history item indicating that the main CPU became unresponsive in normal status |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Main CPU Abnormal Reset Record |
A history item indicating that the main CPU was reset, although the power switch was not turned off in normal status |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Image Processing IC Written Protect Record |
A history item indicating that the image processing IC memory was write protected |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Image Processing IC Initialized Malfunction Record |
A history item indicating that the image processing IC memory was not initialized |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Main EEPROM Access Status |
Main EEPROM access status |
Normal/Abnormal |
Normal: Television camera controller is normal Abnormal: Television camera controller is abnormal |
- |
|
Sub EEPROM Access Status |
Sub-EEPROM access status |
Normal/Abnormal |
Normal: Television camera controller is normal Abnormal: Television camera controller is abnormal |
- |
|
System Power Supply Voltage Malfunction Record |
A history item indicating an abnormally generated-voltage value from the system power source |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Main CPU Starting Malfunction Record |
A history item indicating that the main CPU did not start |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
CAN CPU Boot Malfunction Record |
A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Wheel Speed Sensor (4wheel) |
Reception state of the vehicle speed signal from the skid control ECU |
Valid/Invalid |
Valid: Speed signal received Invalid: Speed signal not received |
- |
|
Bus-off Continuation Detection Record |
A history item indicating that the bus off condition was detected |
No/Yes |
No: Television camera controller is normal Yes: Television camera controller is abnormal |
- |
|
Shift R Position |
Reverse signal |
ON/OFF |
OFF: Shift lever in any position except R ON: Shift lever in R |
- |
|
Camera Changing SW Signal Status |
Signal status at the BLSW terminal (switch camera signal) |
ON/OFF |
ON: Panoramic view monitor switch on OFF: Panoramic view monitor switch off |
- |
|
Back Camera Availability Consistency |
Status of ECU stored in rear television camera assembly |
OK/NG |
OK: Normal NG: Rear television camera assembly or television camera controller is abnormal |
- |
|
Side Camera LH Availability Consistency |
Status of ECU stored in side television camera assembly LH |
OK/NG |
OK: Normal NG: Side television camera assembly LH or television camera controller is abnormal |
- |
|
Front Camera Availability Consistency |
Status of ECU stored in front television camera assembly |
OK/NG |
OK: Normal NG: Front television camera assembly or television camera controller is abnormal |
- |
|
Side Camera RH Availability Consistency |
Status of ECU stored side television camera assembly RH |
OK/NG |
OK: Normal NG: Side television camera assembly RH or television camera controller is abnormal |
- |
|
Image Adjustment Status |
Status of the image adjustment status |
Incomplete/Processing/Complete |
Incomplete: Image adjustment incomplete Processing: Image adjustment in processing Complete: Image adjustment completed |
- |
|
Number of DTC |
Number of DTCs (past and present) |
Min: 0, Max: 255 |
Changes according to the number of DTCs output |
- |
Chassis > Parking Assist Camera > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Wheel Speed Sensor (4wheel) |
Reception state of the vehicle speed signal from the skid control ECU |
Valid/Invalid |
Valid: Speed signal received Invalid: Speed signal not received |
- |
|
Video Output Status |
Output condition of video signal |
OK or NG |
OK: Output condition of video signal is normal NG: Output condition of video signal is abnormal |
- |
|
Circumference Monitoring System Type Check |
Verification of rear television camera assembly signal |
OK or NG |
OK: Rear television camera assembly normal NG: Rear television camera assembly abnormal |
- |
|
EEPROM Status (Initial read) |
Rear television camera assembly information |
OK or NG |
OK: Rear television camera assembly normal NG: Rear television camera assembly abnormal |
- |
|
CPU Communication Status |
Rear television camera assembly information |
OK or NG |
OK: Rear television camera assembly normal NG: Rear television camera assembly abnormal |
- |
|
Number of DTC |
Number of stored DTCs |
min.: 0, max.: 255 |
Number of DTCs will be displayed |
- |
|
Current Key Cycle |
Cumulative number of times the power switch was turned on (IG) |
Min.: 0, Max.: 65535 time |
Cumulative number of times the power switch was turned on (IG) will be displayed |
- |
|
Current Key Cycle Elapsed Time |
Time elapsed since the power switch was turned on (IG) |
Min.: 0, Max.: 1677721.5 s |
Time elapsed since the power switch was turned on (IG) will be displayed |
- |
|
|