Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM10000000162DX |
Model Year Start: 2018 |
Model: Camry HV |
Prod Date Range: [07/2017 -
] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: INSTALLATION; 2018 - 2024 MY Camry HV [07/2017 - ] |
INSTALLATION
PROCEDURE
1. INSTALL AIRBAG SENSOR ASSEMBLY
(a) Check that the power switch is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Install the airbag sensor assembly with the 3 bolts.
Torque:
17.5 N·m {178 kgf·cm, 13 ft·lbf}
NOTICE:
-
Temporarily tighten the 2 bolts in the order of (A), (B) and then fully tighten the 3 bolts in the order of (C), (A) and (B).
-
If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
-
When installing the airbag sensor assembly, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
-
When the power switch is first turned to on (IG) after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.
|
|
(d) Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connectors.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
*a
|
Lock Lever
|
|
Move in this Direction
|
(e) Check that there is no looseness in the installed parts of the airbag sensor assembly.
2. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Air Duct)
(a) Install the No. 1 console box duct with the clip as shown in the illustration.
|
Install in this Direction
|
3. INSTALL FRONT FLOOR CARPET ASSEMBLY
(a) Install the front floor carpet assembly to its original position as shown in the illustration.
|
|
(b) Engage the 2 guides.
(c) Install the 2 front floor carpet clips.
(d) Install the front floor carpet assembly to its original position as shown in the illustration.
|
|
(e) Engage the 2 guides.
(f) Install the 2 front floor carpet clips.
4. INSTALL ACCELERATOR PEDAL
Click here
5. INSTALL ACCELERATOR PEDAL PAD
Click here
6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
7. INSTALL LOWER CENTER PILLAR GARNISH LH
Click here
8. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
9. INSTALL REAR DOOR SCUFF PLATE LH
Click here
10. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
12. INSTALL FRONT DOOR SCUFF PLATE LH
Click here
13. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
14. INSTALL LOWER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
16. INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
17. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here
19. INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
20. INSTALL CONSOLE BOX ASSEMBLY
Click here
21. INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat: Click here
for Power Seat: Click here
22. INSTALL FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
for Manual Seat: Click here
for Power Seat: Click here
23. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
24. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION
(a) When the airbag sensor assembly is replaced, perform zero point learning for the yaw rate and acceleration sensor.
Click here
HINT:
The yaw rate and acceleration sensor is built into the airbag sensor assembly.
|