| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000162DU |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - 10/2020] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: REAR SEAT SIDE AIRBAG ASSEMBLY: REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Lighting system (w/ AFS)(EXT) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
Click here
![2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
If a rear seat airbag assembly has been deployed, replace the rear seat airbag assembly, rear side seatback frame sub-assembly, rear side seatback pad and rear side seatback cover sub-assembly with the necessary parts in accordance with the extent of the collision damage.
Click here
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
4. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear side seatback assembly.
7. REMOVE REAR SIDE SEATBACK ASSEMBLY
Click here
8. REMOVE REAR SEAT SHOULDER BELT GUIDE
Click here
9. REMOVE REAR SIDE SEATBACK COVER WITH PAD
Click here
10. REMOVE REAR SEAT AIRBAG ASSEMBLY
CAUTION:
When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side |
|
(a) Disengage the clamp. |
|
(b) Disconnect the wire harness from the wire harness clamp.
(c) Remove the 2 nuts and rear seat airbag assembly.
NOTICE:
- Do not reuse the nuts.
- Make sure that the rear side seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.
|
|