HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P310711; Lost Communication with Airbag System Control Module Circuit Short to Ground; 2018 - 2024 MY Camry HV [07/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000015LP7
Model Year Start: 2018	Model: Camry HV	Prod Date Range: [07/2017 - ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P310711; Lost Communication with Airbag System Control Module Circuit Short to Ground; 2018 - 2024 MY Camry HV [07/2017 - ]

DTC

P310711

Lost Communication with Airbag System Control Module Circuit Short to Ground

DESCRIPTION

The hybrid vehicle control ECU assembly detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P310711

Lost Communication with Airbag System Control Module Circuit Short to Ground

Short to ground in the communication circuit:

Communication from the airbag sensor assembly stopped and Circuit Low has been detected for a certain period.

(1 trip detection logic)

Wire harness or connector
Airbag sensor assembly
Hybrid vehicle control ECU assembly

Does not come on

Master Warning Light:

Comes on

Related Data List

DTC No.	Data List
P310711	Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here

Connect the Techstream to the DLC3.
Turn the power switch on (IG) and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the Techstream on.
With power switch on (IG) and wait for 2 minutes or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.

WIRING DIAGRAM

PROCEDURE

1.	CHECK DTC OUTPUT (SRS AIRBAG)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result	Proceed to
Airbag system DTCs are not output.	A
Airbag system DTCs are output.	B

(e) Turn the power switch off.

GO TO DTC CHART (AIRBAG SYSTEM)

2.	CHECK AIR BAG SENSOR ASSEMBLY (CHECK WAVEFORM)

(a) Connect an oscilloscope between the hybrid vehicle control ECU assembly terminals specified in the table below.

(b) Turn the power switch on (READY).

Item	Contents
Terminal	K70-14 (ABFS) - K69-6 (E1)
Equipment Setting	5 V/DIV., 150 ms./DIV.
Condition	Power switch on (READY)

Result:

Result	Proceed to
The waveform appears as shown in the illustration.	A
The waveform differs from the one shown in the illustration.	B

*a	Component with harness connected (Hybrid Vehicle Control ECU Assembly)

(d) Turn the power switch off.

GO TO STEP 6

CLEAR DTC

Click here

4.	CHECK DTC OUTPUT (HYBRID CONTROL)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Result	Proceed to
P310711 is not output.	A
P310711 is output.	B

(e) Turn the power switch off.

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

5.	CHECK FOR INTERMITTENT PROBLEMS

Click here

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.	CHECK AIR BAG SENSOR ASSEMBLY

(a) Disconnect the K73 airbag sensor assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
K73-24 (GSW2) - K73-33 (E1)	Power switch off	10 kΩ or higher

*a	Component without harness connected (Airbag sensor Assembly)

REPLACE AIR BAG SENSOR ASSEMBLY

7.	CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - AIRBAG SENSOR ASSEMBLY)

(a) Disconnect the K70 hybrid vehicle control ECU assembly connector.

(b) Disconnect the K73 airbag sensor assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
K70-14 (ABFS) or K73-24 (GSW2) - Body ground and other terminals	Power switch off	10 kΩ or higher

Rear view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

Front view of wire harness connector

(to Airbag Sensor Assembly)

(d) Reconnect the K73 airbag sensor assembly connector.

(e) Reconnect the K70 hybrid vehicle control ECU assembly connector.

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR