| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000015GUH |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - ] |
| Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: U0125,U0126,U0129,U0142,U0293; Lost Communication with Yaw Rate Sensor Module; 2018 - 2024 MY Camry HV [07/2017 - ] | ||
|
DTC |
U0125 |
Lost Communication with Yaw Rate Sensor Module |
|
DTC |
U0126 |
Lost Communication with Steering Angle Sensor Module |
|
DTC |
U0129 |
Lost Communication with Brake System Control Module |
|
DTC |
U0142 |
Lost Communication with Body Control Module "B" |
|
DTC |
U0293 |
Lost Communication with Hybrid Control Module |
DESCRIPTION
These DTCs are stored if there is a malfunction in the CAN communication system connected to the blind spot monitor sensor.
HINT:
If CAN communication system DTCs are stored, they may also be stored for other systems.
Blind Spot Monitor Master
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
U0125 |
Lost Communication with Yaw Rate Sensor Module |
Lost communication with yaw rate and acceleration sensor |
CAN communication system |
|
U0126 |
Lost Communication with Steering Angle Sensor Module |
Lost communication with steering sensor |
CAN communication system |
|
U0129 |
Lost Communication with Brake System Control Module |
Lost communication with brake system |
CAN communication system |
|
U0142 |
Lost Communication with Body Control Module "B" |
Lost communication with main body ECU |
CAN communication system |
|
U0293 |
Lost Communication with Hybrid Control Module |
Lost communication with hybrid vehicle control ECU assembly |
CAN communication system |
Blind Spot Monitor Slave
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
U0125 |
Lost Communication with Yaw Rate Sensor Module |
Lost communication with yaw rate and acceleration sensor |
CAN communication system |
|
U0126 |
Lost Communication with Steering Angle Sensor Module |
Lost communication with steering sensor |
CAN communication system |
|
U0129 |
Lost Communication with Brake System Control Module |
Lost communication with brake system |
CAN communication system |
|
U0142 |
Lost Communication with Body Control Module "B" |
Lost communication with main body ECU |
CAN communication system |
|
U0293 |
Lost Communication with Hybrid Control Module |
Lost communication with hybrid vehicle control ECU assembly |
CAN communication system |
CAUTION / NOTICE / HINT
NOTICE:
When checking for DTCs, make sure that the blind spot monitor system is turned on.
PROCEDURE
|
1. |
CHECK DTC |
(a) Turn the power switch off.
(b) Turn the power switch on (IG).
(c) Recheck for DTCs and check if the same DTC is output again.
Body Electrical > Blind Spot Monitor Master > Trouble Codes
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are output |
A |
|
No DTCs are output |
B |
HINT:
- If CAN communication system DTCs are stored, they may also be stored for other systems.
- If the CAN communication system has been inspected and repaired, the DTCs will not be output when rechecking for DTCs.
-
If these DTCs are output frequently, duplicate the conditions that cause the problem symptoms and perform troubleshooting again, even though the DTC was not output when rechecking for DTCs.
Click here
![2018 MY Camry HV [07/2017 - 09/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
| A |
|
| B |
|
USE SIMULATION METHOD TO CHECK
|
|
|