| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000015C1G |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B163B,B163C,B1699; Side Airbag Sensor Assembly No.2 Lost Communication (LH); 2018 - 2024 MY Camry HV [07/2017 - ] | ||
|
DTC |
B163B |
Side Airbag Sensor Assembly No.2 Lost Communication (LH) |
|
DTC |
B163C |
Side Airbag Sensor Assembly No.2 Initialization Error (LH) |
|
DTC |
B1699 |
No.2 Side Satellite Sensor Bus LH Initialization Incomplete |
DESCRIPTION
The side collision sensor LH circuit (bus 2) consists of the airbag sensor assembly and side No. 1 airbag sensor LH.
The side No. 1 airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 2).
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Warning Indicate |
Test Mode / Check Mode |
|---|---|---|---|---|---|
|
B163B |
Side Airbag Sensor Assembly No.2 Lost Communication (LH) |
|
|
Comes on |
Does not apply to test/check mode |
|
B163C |
Side Airbag Sensor Assembly No.2 Initialization Error (LH) |
|
|
Comes on |
Does not apply to test/check mode |
|
B1699 |
No.2 Side Satellite Sensor Bus LH Initialization Incomplete |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK CONNECTION OF CONNECTORS |
(a) Turn the power switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the airbag sensor assembly and side No. 1 airbag sensor LH.
OK:
The connectors are properly connected.
| NG |
|
CONNECT CONNECTORS PROPERLY |
|
|
2. |
CHECK CONNECTORS |
(a) Disconnect the connectors from the airbag sensor assembly and side No. 1 airbag sensor LH.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG |
|
REPLACE FLOOR WIRE |
|
|
3. |
CHECK FLOOR WIRE |
|
(a) Connect the cable to the negative (-) auxiliary battery terminal. |
|
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R36-2 (BFL+) - Body ground |
Power switch on (IG) |
Below 1 V |
|
R36-1 (BFL-) - Body ground |
Power switch on (IG) |
Below 1 V |
(d) Turn the power switch off.
(e) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(f) Using a service wire, connect terminals 29 (BCL+) and 30 (BCL-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R36-2 (BFL+) - R36-1 (BFL-) |
Always |
Below 1 Ω |
(h) Disconnect the service wire from connector B.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R36-2 (BFL+) - R36-1 (BFL-) |
Always |
1 MΩ or higher |
|
R36-2 (BFL+) - Body ground |
Always |
1 MΩ or higher |
|
R36-1 (BFL-) - Body ground |
Always |
1 MΩ or higher |
| NG |
|
REPLACE FLOOR WIRE |
|
|
4. |
CHECK SIDE NO. 1 AIRBAG SENSOR LH |
|
(a) Connect the connector to the airbag sensor assembly. |
|
(b) Interchange the side No. 1 airbag sensor LH with RH and connect the connectors.
(c) Connect the cable to the negative (-) auxiliary battery terminal.
(d) Turn the power switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
(f) Turn the power switch off.
(g) Turn the power switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
HINT:
Codes other than DTCs B162B, B162C, B163B, B163C, B1694 and B1699 may be output at this time, but they are not related to this check.
|
Result |
Proceed to |
|---|---|
|
DTC B163B, B163C or B1699 is output. |
A |
|
DTC B162B, B162C or B1694 is output. |
B |
|
DTCs B162B, B162C, B163B, B163C, B1694 and B1699 are not output. |
C |
(i) Turn the power switch off.
(j) Disconnect the cable from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(k) Return the side No. 1 airbag sensor LH and RH to their original positions and connect the connectors.
| A |
|
REPLACE AIRBAG SENSOR ASSEMBLY
|
| B |
|
REPLACE SIDE NO. 1 AIRBAG SENSOR LH
|
| C |
|
USE SIMULATION METHOD TO CHECK
|
|
|