Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000015C0T
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1612,B1613; Front Airbag Sensor Lost Communication (RH); 2018 - 2024 MY Camry HV [07/2017 -        ]

DTC

B1612

Front Airbag Sensor Lost Communication (RH)

DTC

B1613

Front Airbag Sensor Initialization Error (RH)

DESCRIPTION

The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1612

Front Airbag Sensor Lost Communication (RH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit.
  • Front airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Instrument panel wire
  • Engine room main wire
  • Front airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

B1613

Front Airbag Sensor Initialization Error (RH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit.
  • Front airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Instrument panel wire
  • Engine room main wire
  • Front airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

(a) Turn the power switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

2.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE INSTRUMENT PANEL WIRE OR ENGINE ROOM MAIN WIRE

OK

3.

CHECK FRONT AIRBAG SENSOR RH CIRCUIT

(a) Connect the connectors that link the engine room main wire and instrument panel wire.

*1

Front Airbag Sensor RH

*2

Airbag Sensor Assembly

*3

Engine Room Main Wire

*4

Instrument Panel Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Front Airbag Sensor RH)

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(c) Turn the power switch on (IG).

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A42-2 (+SR) - Body ground

Power switch on (IG)

Below 1 V

A42-1 (-SR) - Body ground

Power switch on (IG)

Below 1 V

(e) Turn the power switch off.

(f) Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A42-2 (+SR) - A42-1 (-SR)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A42-2 (+SR) - A42-1 (-SR)

Always

1 MΩ or higher

A42-2 (+SR) - Body ground

Always

1 MΩ or higher

A42-1 (-SR) - Body ground

Always

1 MΩ or higher

NG

GO TO STEP 5

OK

4.

CHECK FRONT AIRBAG SENSOR RH

(a) Connect the connector to the airbag sensor assembly.

*1

Front Airbag Sensor LH

*2

Airbag Sensor Assembly

(b) Interchange the front airbag sensor RH with LH and connect the connectors.

(c) Connect the cable to the negative (-) auxiliary battery terminal.

(d) Turn the power switch on (IG), and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the power switch off.

(g) Turn the power switch on (IG), and wait for at least 60 seconds.

(h) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.

Result

Proceed to

DTCs B1612, B1613, B1617 and B1618 are not output.

A

DTC B1617 or B1618 is output.

B

DTC B1612 or B1613 is output.

C

(i) Turn the power switch off.

(j) Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(k) Return the front airbag sensor RH and LH to their original positions and connect the connectors.

A

USE SIMULATION METHOD TO CHECK 2018 MY Camry HV [07/2017 - 09/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry HV [09/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry HV [09/2019 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry HV [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry HV [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

B

REPLACE FRONT AIRBAG SENSOR RH 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT AIRBAG SENSOR: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT AIRBAG SENSOR: REMOVAL

C

REPLACE AIRBAG SENSOR ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

5.

CHECK INSTRUMENT PANEL WIRE

(a) Disconnect the instrument panel wire connector from the engine room main wire.

*1

Front Airbag Sensor RH

*2

Airbag Sensor Assembly

*3

Engine Room Main Wire

*4

Instrument Panel Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Engine Room Main Wire)

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(c) Turn the power switch on (IG).

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

AK6-1 (+SR) - Body ground

Power switch on (IG)

Below 1 V

AK6-3 (-SR) - Body ground

Power switch on (IG)

Below 1 V

(e) Turn the power switch off.

(f) Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 29 (+SR) and 28 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

AK6-1 (+SR) - AK6-3 (-SR)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

AK6-1 (+SR) - AK6-3 (-SR)

Always

1 MΩ or higher

AK6-1 (+SR) - Body ground

Always

1 MΩ or higher

AK6-3 (-SR) - Body ground

Always

1 MΩ or higher

OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE