| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000158HE |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - ] |
| Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF SYSTEM: B2341,B2344; Sensor (Motor) Failure; 2018 - 2024 MY Camry HV [07/2017 - ] | ||
|
DTC |
B2341 |
Sensor (Motor) Failure |
|
DTC |
B2344 |
Position Failure |
DESCRIPTION
When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.
When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B2341 |
Sensor (Motor) Failure |
Sensor (motor) failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the motor) |
|
|
B2344 |
Position Failure |
Position failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the gear position) |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click here
![2018 - 2024 MY Camry HV [07/2017 - ]; SLIDING ROOF / CONVERTIBLE: SLIDING ROOF SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK SLIDING ROOF OPERATION |
(a) Check the sliding roof auto operation.
Click here
OK:
Auto operation operates normally.
| NG |
|
|
|
2. |
CHECK DTC OUTPUT |
(a) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs
(b) Check for DTCs.
Body Electrical > Sliding Roof > Trouble Codes
OK:
DTCs B2341 and B2344 are not output.
| OK |
|
USE SIMULATION METHOD TO CHECK
|
| NG |
|
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
|
|
3. |
INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) |
(a) Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
Click here
OK:
Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
| NG |
|
|
|
4. |
CHECK DTC OUTPUT |
(a) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs
(b) Check for DTCs.
Body Electrical > Sliding Roof > Trouble Codes
OK:
DTCs B2341 and B2344 are not output.
| OK |
|
END (MALFUNCTION DUE TO INITIALIZATION FAILURE) |
| NG |
|
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
|
|
5. |
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND) |
(a) Disconnect the V14 sliding roof switch (roof console box sub-assembly) connector.
(b) Disconnect the V2 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
V2-8 (CLS) - V14-4 (CLS) |
Always |
Below 1 Ω |
|
V2-8 (CLS) or V14-4 (CLS) - Body ground |
Always |
10 kΩ or higher |
|
V2-10 (OPN) - V14-5 (OPN) |
Always |
Below 1 Ω |
|
V2-10 (OPN) or V14-5 (OPN) - Body ground |
Always |
10 kΩ or higher |
|
V2-9 (CLS) - V14-18 (DOWN) |
Always |
Below 1 Ω |
|
V2-9 (CLS) or V14-18 (DOWN) - Body ground |
Always |
10 kΩ or higher |
|
V2-5 (OPN) - V14-3 (UP) |
Always |
Below 1 Ω |
|
V2-5 (OPN) or V14-3 (UP) - Body ground |
Always |
10 kΩ or higher |
|
V14-15 (GND) - Body ground |
Always |
Below 1 Ω |
|
V2-2 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Remove the sliding roof switch (roof console box sub-assembly).
Click here
(b) Inspect the sliding roof switch (roof console box sub-assembly).
Click here
| OK |
|
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
|
| NG |
|
|
|