Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000156YE
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 10/2020]
Title: SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replacement Part or Procedure

Necessary Procedures

Effects / Inoperative when not performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Occupant detection ECU
  • Front passenger seat

Zero point calibration (Occupant classification system)
  • Occupant classification system
  • Passenger airbag ON/OFF indicator
  • Airbag system (Front passenger side)
  • Seat belt warning system (Front passenger)

2018 - 2024 MY Camry HV [07/2017 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: OCCUPANT CLASSIFICATION SYSTEM: INITIALIZATION

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:

  • If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Camry HV [09/2019 - 10/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE FRONT SEAT HEADREST ASSEMBLY

(a) Remove the front seat headrest assembly from the front seat assembly.

4. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER

(a) Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

(b) Disengage the claw to remove the front outer seat track bracket cover.

Remove in this Direction

5. REMOVE FRONT INNER SEAT TRACK BRACKET COVER

(a) Disengage the claw to remove the front inner seat track bracket cover.

Remove in this Direction

6. REMOVE REAR OUTER SEAT TRACK BRACKET COVER

(a) Operate the seat track adjusting handle and move the front seat assembly to the foremost position.

(b) Disengage the claw to remove the rear outer seat track bracket cover.

Remove in this Direction

7. REMOVE REAR INNER SEAT TRACK BRACKET COVER

(a) Disengage the claw to remove the rear inner seat track bracket cover.

Remove in this Direction

8. REMOVE FRONT SEAT ASSEMBLY

(a) Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.

(b) Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

(c) Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.

(d) Operate the vertical adjusting handle and move the front seat assembly to the uppermost position.

(e) Operate the seat track adjusting handle and move the front seat assembly to the center position.

(f) Operate the reclining adjuster release handle and move the seatback to the upright position.

(g) Disconnect the front seat airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a

White Housing Lock

*b

Yellow CPA

Slide

(2) Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.

(h) Disconnect each connector and disengage each clamp under the front seat assembly.

(i) Remove the front seat assembly.

NOTICE:

Be careful not to damage the vehicle body.