| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000154CE |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - 10/2020] |
| Title: SEAT: REAR SEAT RECLINING CONTROL CABLE: REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seatback lock assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Lighting system (w/ AFS)(EXT) |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
CAUTION:
-
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. REMOVE SPARE WHEEL COVER ASSEMBLY
Click here
2. REMOVE REAR SEAT ASSEMBLY
Click here
3. REMOVE CENTER STOP LIGHT SET
Click here
4. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD
|
(a) Remove the luggage compartment trim inner pad. |
|
5. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
Click here
6. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
7. REMOVE INNER ROOF SIDE GARNISH LH
Click here
8. REMOVE INNER ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
9. REMOVE REAR SEAT SHOULDER BELT HOLE COVER
Click here
10. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
|
(a) Remove the 2 clips. |
|
|
(b) Disengage the 3 clips and 5 guides. |
|
(c) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
11. REMOVE ROOM PARTITION BOARD LH
|
(a) Remove the clip. |
|
|
(b) Disengage the 2 claws. |
|
(c) Disengage the 4 clips to remove the room partition board LH.
12. REMOVE ROOM PARTITION BOARD RH
|
(a) Remove the 2 clips. |
|
|
(b) Disengage the 5 clips to remove the room partition board RH. |
|
13. REMOVE REAR SEATBACK LOCK ASSEMBLY LH
(a) Release the stopper and disengage the guide as shown in the illustration.
|
*a |
Stopper |
|
Release |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
(b) Remove the 2 nuts and rear seatback lock assembly LH. |
|
14. REMOVE REAR SEATBACK LOCK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
|
|