Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM10000000154CB |
Model Year Start: 2018 |
Model: Camry HV |
Prod Date Range: [07/2017 -
] |
Title: SEAT: REAR SEAT ASSEMBLY: INSTALLATION; 2018 - 2024 MY Camry HV [07/2017 - ] |
INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
(a) Place the rear side seatback assembly LH in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
(b) Engage the hook and install the rear side seatback assembly LH with the bolt.
Torque:
18 N·m {184 kgf·cm, 13 ft·lbf}
|
|
(c) Connect the connector.
(1) Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.
*a
|
Correct
|
*b
|
Incorrect
|
*c
|
Yellow CPA
|
*d
|
White housing lock
|
(2) Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).
NOTICE:
-
When connecting any airbag connector, take care not to damage the airbag wire harness.
-
When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.
(d) Connect the rear seat outer belt LH to the rear seat shoulder belt guide LH.
2. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
3. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Click here
5. INSTALL REAR SEATBACK ASSEMBLY LH
(a) Place the rear seatback assembly LH in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
(b) Engage the 2 guides.
(c) Install the rear seatback assembly LH with the 2 bolts.
Torque:
36.8 N·m {375 kgf·cm, 27 ft·lbf}
(d) Return the rear seatback assembly LH to its original position.
6. INSTALL REAR SEATBACK ASSEMBLY RH
(a) Place the rear seatback assembly RH in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
(b) Engage the 2 guides.
(c) Install the rear seatback assembly RH with the 2 bolts.
Torque:
36.8 N·m {375 kgf·cm, 27 ft·lbf}
(d) Return the rear seatback assembly RH to its original position.
7. INSTALL REAR SEAT CUSHION LOCK HOOK
(a) Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
HINT:
Use the same procedure for the RH side and LH side.
|
Install in this Direction
|
8. INSTALL REAR SEAT CUSHION ASSEMBLY
(a) Place the rear seat cushion assembly in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
(b) Install the rear seat cushion assembly as shown in the illustration.
|
Install in this Direction
|
(c) When reusing the rear seat inner belt assembly RH and rear center seat outer belt assembly:
(1) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly through the rear seat cushion assembly as shown in the illustration.
|
|
(2) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly as shown in the illustration.
|
|
(3) Connect the rear seat inner belt assembly RH with the bolt and washer.
(4) Install the rear seat inner belt assembly RH and rear center seat outer belt assembly as a set with the bolt.
|
Protruding Part
|
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
-
Install the rear seat inner belt assembly RH with the arrow on the anchor part facing the front of the vehicle.
-
Do not allow the anchor part of the rear seat inner belt assembly RH to overlap the protruding parts of the floor panel.
(d) Engage the 2 rear seat cushion frame hooks as shown in the illustration to install the rear seat cushion assembly.
*a
|
Rear Seat Cushion Frame Hook
|
|
Install in this Direction
|
NOTICE:
Confirm that the rear seat cushion assembly is securely installed.
(e) When installing a new rear seat inner belt assembly RH and rear center seat outer belt assembly:
(1) Connect the rear center seat outer belt assembly as shown in the illustration.
|
|
9. INSTALL REAR SEAT HEADREST ASSEMBLY LH (w/ Removable Headrest)
(a) Install the rear seat headrest assembly LH.
10. INSTALL REAR SEAT HEADREST ASSEMBLY RH (w/ Removable Headrest)
(a) Install the rear seat headrest assembly RH.
11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
12. INSTALL LUGGAGE TRIM SERVICE HOLE COVER
Click here
13. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
14. INSPECT SRS WARNING LIGHT
Click here
|