HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): Shift Paddle Switch Circuit; 2018 - 2024 MY Camry HV [07/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM100000001543C
Model Year Start: 2018	Model: Camry HV	Prod Date Range: [07/2017 - ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): Shift Paddle Switch Circuit; 2018 - 2024 MY Camry HV [07/2017 - ]

Shift Paddle Switch Circuit

DESCRIPTION

Moving the shift lever to S enables the shift range to be selected. The shift range can be selected by operating the "+" or "-" shift paddle switch.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE

1.	READ VALUE USING TECHSTREAM (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift UP Signal, Sports Shift DOWN Signal.

Powertrain > Hybrid Control > Data List

Tester Display
Sports Shift UP Signal
Sports Shift DOWN Signal

(d) Read the values displayed on the Techstream.

Result	Proceed to
The Techstream display changes according to the shift paddle switch (transmission shift switch assembly) operation.	A
The Techstream display does not change according to the shift paddle switch (transmission shift switch assembly) operation.	B

(e) Turn the power switch off.

CHECK FOR INTERMITTENT PROBLEMS

2.	CHECK HARNESS AND CONNECTOR (SHIFT PADDLE SWITCH CIRCUIT)

(a) Disconnect the K70 hybrid vehicle control ECU assembly connector.

(b) Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.

(c) Measure the resistance according to the value(s) in the table below when the shift paddle switch (transmission shift switch assembly) is moved to each position.

Standard Resistance:

Tester Connection	Condition	Specified Condition
K70-9 (SFTU) - Body ground	Shift paddle switch RH (+) operated	3 Ω or less
K70-8 (SFTD) - Body ground	Shift paddle switch LH (-) operated	3 Ω or less
K70-9 (SFTU) - Body ground	Shift paddle switch RH (+) not operated	10 kΩ or higher
K70-8 (SFTD) - Body ground	Shift paddle switch LH (-) not operated	10 kΩ or higher

*a	Rear view of wire harness connector (to Hybrid Vehicle Control ECU Assembly)

(d) Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.

(e) Reconnect the K70 hybrid vehicle control ECU assembly connector.

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.	CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

(a) Disconnect the K22 spiral cable sub-assembly connector.

*a	Front view of wire harness connector (to Spiral Cable Sub-assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance (Open):

Tester Connection	Condition	Specified Condition
K22-2 (ECC) - Body ground	Always	Below 1 Ω

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.	CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

(a) Disconnect the K70 hybrid vehicle control ECU assembly connector.

(b) Disconnect the K22 spiral cable with sensor sub-assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
K70-9 (SFTU) - K22-8 (SUP)	Always	Below 1 Ω
K70-8 (SFTD) - K22-1 (SDN)	Always	Below 1 Ω
K70-9 (SFTU) or K22-8 (SUP) - Body ground	Always	10 kΩ or higher
K70-8 (SFTD) or K22-1 (SDN)- Body ground	Always	10 kΩ or higher

Rear view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

Front view of wire harness connector

(to Spiral Cable Sub-assembly)

(d) Reconnect the K22 spiral cable with sensor sub-assembly connector.

(e) Reconnect the K70 hybrid vehicle control ECU assembly connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.	INSPECT SPIRAL CABLE SUB-ASSEMBLY

(a) Inspect the spiral cable sub-assembly.

Click here

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.	INSPECT SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

(a) Inspect the shift paddle switch LH (transmission shift switch assembly).

Click here

REPLACE SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

7.	INSPECT SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

(a) Inspect the shift paddle switch RH (transmission shift switch assembly).

Click here

REPLACE SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

8.	INSPECT NO. 1 SWITCH WIRE

(a) Disconnect the z4 No. 1 switch wire connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
z4-2 (SUP) - z4-3 (ECC)	"+" (Up shift) shift paddle switch operated and held	Below 1 Ω
z4-2 (SUP) - z4-3 (ECC)	"+" (Up shift) shift paddle switch not operated	10 kΩ or higher
z4-4 (SDN) - z4-3 (ECC)	"-" (Down shift) shift paddle switch operated and held	Below 1 Ω
z4-4 (SDN) - z4-3 (ECC)	"-" (Down shift) shift paddle switch not operated	10 kΩ or higher

*a	Front view of wire harness connector (to Spiral Cable Sub-assembly)

CHECK FOR INTERMITTENT PROBLEMS

REPLACE NO. 1 SWITCH WIRE