Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000153PT
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 10/2020]
Title: A25A-FXS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL illuminates

2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

  • Gas leak from exhaust system is repaired
  • Replacement of engine coolant temperature sensor

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2018 MY Camry HV [07/2017 - 09/2018]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION 2019 MY Camry HV [09/2018 - 09/2019]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION 2020 MY Camry HV [09/2019 - 10/2020]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Replacement of inverter with converter assembly

Resolver learning
  • DTCs are stored
  • Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
  • Shock or vibration during acceleration

2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): UTILITY for Nickel Metal Hydride Battery

2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): UTILITY for Lithium-ion Battery

Replacement of hybrid vehicle transaxle assembly
  • Resolver learning
  • Initialize resolver

Front wheel alignment adjustment
  1. Clear zero point calibration data.
  2. Perform yaw rate and acceleration sensor zero point calibration.
  • DTCs are stored
  • ABS warning light illuminates
  • Brake warning light / yellow (minor malfunction) illuminates
  • Slip indicator light illuminates
  • VSC disabled or malfunctions

2018 MY Camry HV [07/2017 - 09/2018]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: CALIBRATION 2019 - 2020 MY Camry HV [09/2018 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: CALIBRATION

Suspension, tires, etc.*1

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION for Calibration

Replacement of front bumper assembly

Front television camera view adjustment

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: CALIBRATION for Calibration

Suspension, tires, etc.*1
  • Television camera controller initialization
  • Adjust steering angle
  • Rear television camera assembly optical axis (Back camera position setting)
  • Replacement of headlight ECU sub-assembly LH
  • Replacement of headlight assembly LH
  • Synchronize the vehicle information
  • Perform headlight ECU sub-assembly LH initialization

Lighting system (w/ AFS)(EXT)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; LIGHTING (EXT): LIGHTING SYSTEM (w/ AFS): INITIALIZATION

Suspension, tires, etc.*1

Perform headlight ECU sub-assembly LH initialization
  • *: When performing learning using the Techstream.

    Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

  • *1: The vehicle height changes because of suspension or tire replacement

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL

2. REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.
  • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
  • Using an engine sling device and engine lift, secure the engine assembly before servicing.

(b) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(c) Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.

3. REMOVE FLYWHEEL SUB-ASSEMBLY

(a) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(b) Remove the 8 bolts and flywheel sub-assembly from the crankshaft.

4. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

(a) Type A:

(1) Remove the No. 1 crankshaft position sensor plate.

(b) Type B:

(1) Remove the No. 1 crankshaft position sensor plate.

5. REMOVE REAR ENGINE OIL SEAL

(a) Using a knife, cut off the lip of the rear engine oil seal.

*a

Protective Tape

*b

Cut Position

(b) Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.