Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000015290 |
Model Year Start: 2018 |
Model: Camry HV |
Prod Date Range: [07/2017 - 09/2018] |
Title: TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION; 2018 MY Camry HV [07/2017 - 09/2018] |
INSPECTION
PROCEDURE
1. INSPECT TIRES
(a) Inspect the tires for wear and proper inflation pressure.
Cold Tire Inflation Pressure:
Tire Size
|
Cold Tire Inflation Pressure
|
Front
|
Rear
|
205/65R16 95H
215/55R17 94V
235/45R18 94V
|
240 kPa (2.4 kgf/cm2, 35 psi)
|
240 kPa (2.4 kgf/cm2, 35 psi)
|
Cold Tire Inflation Pressure (for Compact Spare Tire):
Tire Size
|
Cold Tire Inflation Pressure
|
T155/70D17 110M
|
420 kPa (4.2 kgf/cm2, 60 psi)
|
(1) Perform initialization.
Click here
(2) Tire pressure adjustment method when warm:
-
Turn the power switch off.
-
Connect the Techstream to the DLC3.
-
Turn the power switch on (IG).
-
Turn the Techstream on.
-
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
-
Adjust the tire pressure so that the displayed value is equal to the set pressure.
-
Perform initialization and check that initialization completes.
Click here
-
Check and record the value of the Data List item "Temperature in Tire". (Ts)
-
Check and record the ambient temperature during tire pressure adjustment. (Tm)
-
Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
HINT:
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
P = (Specified Pressure) + (Ts - Tm)
-
Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
(b) Using a dial indicator, check the runout of the tires.
Maximum Tire Runout:
1.4 mm (0.0551 in.)
HINT:
Measure the runout with the wheel assembly removed from the vehicle.
|
|
2. ROTATE TIRES
(a) Remove the wheel assembly.
Click here
(b) Rotate the tires as shown in the illustration.
|
Front
|
(c) Install the wheel assembly.
Click here
(d) Perform initialization.
Click here
3. INSPECT AND ADJUST WHEEL BALANCE
(a) Inspect and adjust the off-the-car balance.
(1) for Steel Wheel:
Maximum Wheel Imbalance:
8.0 g (0.0176 lb)
HINT:
-
Use clip-on type balance weights for both the inner and outer side.
-
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
(2) except Steel Wheel:
Maximum Wheel Imbalance:
8.0 g (0.0176 lb)
NOTICE:
-
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
-
Do not touch the adhesive surface of the balance weight.
-
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
-
Push the balance weight with your finger to securely adhere it to the desired position.
-
Do not reuse balance weights.
-
Use only TOYOTA genuine stick-on type balance weights or equivalent.
HINT:
-
Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.
-
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
|
|
4. INSPECT FRONT AXLE HUB BEARING
Click here
5. INSPECT REAR AXLE HUB BEARING
Click here
|