Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001513O
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): B2278; Engine/Power Switch Malfunction; 2018 - 2024 MY Camry HV [07/2017 -        ]

DTC

B2278

Engine/Power Switch Malfunction

DESCRIPTION

This DTC is stored when the SSW1 contact signal and SSW2 contact signal, which are detected when the power switch is operated, do not match.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B2278

Engine/Power Switch Malfunction

When the power switch is operated, the SSW1 contact signal and SSW2 contact signal do not match (1-trip detection logic*).

  • Power switch
  • Certification ECU (smart key ECU assembly)
  • Wire harness or connector

DTC Output Confirmation Operation:

  • Turn the power switch on (IG).
  • *: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Function when Malfunction Detected

If either the SSW1 contact signal or SSW2 contact signal is stuck on, the power source mode cannot be changed by pressing the power switch. If either the SSW1 contact signal or SSW2 contact signal is stuck off, emergency stop by pressing and holding the power switch for 2 seconds or more cannot be operated.

-

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2278

Power Source Control

  • Start Switch1
  • Start Switch2

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here 2018 - 2022 MY Camry HV [07/2017 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry HV [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

READ VALUE USING TECHSTREAM (START SWITCH1, START SWITCH2)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Power Source Control / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Power Source Control > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Start Switch1

Power switch 1 status

OFF or ON

OFF: Power switch not pressed

ON: Power switch pressed

  • If the power switch is pressed for a short time, the display may not change.
  • Use this item to determine if the power switch input signal is malfunctioning.

Start Switch2

Power switch 2 status

OFF or ON

OFF: Power switch not pressed

ON: Power switch pressed

  • Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.
  • Behaves the same way as power switch 1.

Body Electrical > Power Source Control > Data List

Tester Display

Start Switch1

Start Switch2

OK:

The Techstream display changes correctly in response to the power switch operation.

NG

GO TO STEP 3

OK

2.

READ VALUE USING TECHSTREAM (START SWITCH1, START SWITCH2)

(a) Enter the following menus: Body Electrical / Power Source Control / Data List.

(b) According to the display on the Techstream, read the Data List while wiggling the wire harness.

Body Electrical > Power Source Control > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Start Switch1

Power switch 1 status

OFF or ON

OFF: Power switch not pressed

ON: Power switch pressed

  • If the power switch is pressed for a short time, the display may not change.
  • Use this item to determine if the power switch input signal is malfunctioning.

Start Switch2

Power switch 2 status

OFF or ON

OFF: Power switch not pressed

ON: Power switch pressed

  • Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.
  • Behaves the same way as power switch 1.

Body Electrical > Power Source Control > Data List

Tester Display

Start Switch1

Start Switch2

OK:

The Techstream display changes correctly in response to the power switch operation.

OK

USE SIMULATION METHOD TO CHECK 2018 MY Camry HV [07/2017 - 09/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry HV [09/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry HV [09/2019 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry HV [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry HV [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

(a) Disconnect the K62 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the K63 power switch connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K62-23 (SSW1) - K63-5 (SS1)

Always

Below 1 Ω

K62-21 (SSW2) - K63-1 (SS2)

Always

Below 1 Ω

K62-11 (AGND) - K63-6 (AGND)

Always

Below 1 Ω

K62-23 (SSW1) or K63-5 (SS1) - Other terminals and body ground

Always

10 kΩ or higher

K62-21 (SSW2) or K63-1 (SS2) - Other terminals and body ground

Always

10 kΩ or higher

K62-11 (AGND) or K63-6 (AGND) - Other terminals and body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

INSPECT POWER SWITCH

(a) Remove the power switch.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (STARTING): POWER SWITCH: REMOVAL

(b) Inspect the power switch.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; A25A-FXS (STARTING): POWER SWITCH: INSPECTION

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

NG

REPLACE POWER SWITCH