Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001513L
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): B2271; Ignition Hold Monitor Malfunction; 2018 - 2024 MY Camry HV [07/2017 -        ]

DTC

B2271

Ignition Hold Monitor Malfunction

DESCRIPTION

This DTC is stored when a malfunction in the IG drive circuit or IG hold circuit of the certification ECU (smart key ECU assembly) or a malfunction in the IG output circuit between the output terminal of the certification ECU (smart key ECU assembly) and IG relay is detected.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B2271

Ignition Hold Monitor Malfunction

When either of the following conditions is met (1-trip detection logic*1):

  • The IG circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*2
  • The IG hold circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*3
  • There is a malfunction in a circuit outside of the certification ECU (smart key ECU assembly) circuit.
  • Certification ECU (smart key ECU assembly)
  • Instrument panel junction block assembly
  • Wire harness or connector

DTC Output Confirmation Operation:

  • Turn the power switch on (IG).
  • *1: Only detected while a malfunction is present and the power switch is on (IG).
  • *2: The IG circuit and IG hold circuit activate the IG relay.
  • *3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit will maintain the power source mode in on (IG).

Vehicle Condition and Fail-safe Function when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Function when Malfunction Detected

The power switch cannot be turned on (IG) (the hybrid control system cannot be started).

The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2271

Power Source Control

  • IG Relay Monitor (Inside)
  • Latch Circuit

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here 2018 - 2022 MY Camry HV [07/2017 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry HV [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (POWER SOURCE)

(a) Disconnect the K62 certification ECU (smart key ECU assembly) connector.

*a

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K62-4 (+B) - Body ground

Power switch off

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

OK

2.

CHECK HARNESS AND CONNECTOR (GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K62-18 (E) - Body ground

Always

Below 1 Ω

*a

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 3A instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K62-17 (IG1D) - 3A-17

Always

Below 1 Ω

K62-17 (IG1D) or 3A-17 - Other terminals and body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Disconnect the 3C instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-17 - 3C-13

Always

Below 1 Ω

3A-17 or 3C-13 - Other terminals

Always

10 kΩ or higher

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

OK

5.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IG2 NO. 1 RELAY)

(a) Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3C-13 - Engine room relay block and junction block assembly IG2 NO. 1 relay terminal 1

Always

Below 1 Ω

3C-13 or engine room relay block and junction block assembly IG2 NO. 1 relay terminal 1 - Other terminals and body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

INSPECT IG2 NO. 1 RELAY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 - 5

Battery voltage not applied between terminals 1 and 2

10 kΩ or higher

3 - 5

Battery voltage applied between terminals 1 and 2

Below 1 Ω

*1

IG2 NO. 1 Relay

NG

REPLACE IG2 NO. 1 RELAY

OK

7.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Disconnect the 3B instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-17 - 3B-3

Always

20 Ω or higher

3A-17 or 3B-3 - Other terminals

Always

10 kΩ or higher

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL