Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000014Z6N |
Model Year Start: 2018 |
Model: Camry HV |
Prod Date Range: [07/2017 - 10/2020] |
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane departure alert system (w/ Steering Control)
|
|
Pre-collision system
|
Intelligent clearance sonar system*
|
Lighting system (w/ AFS)(EXT)
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Panoramic view monitor system
|
|
-
Rear door glass sub-assembly
-
Rear door glass run
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER
Click here
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here
5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
6. REMOVE REAR ARMREST ASSEMBLY
Click here
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Click here
9. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Click here
10. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
11. REMOVE REAR DOOR NO. 1 VENT SEAL
Click here
12. REMOVE REAR DOOR PANEL PROTECTOR
Click here
13. REMOVE REAR DOOR GLASS RUN
Click here
14. DISCONNECT REAR DOOR WEATHERSTRIP
(a) Disconnect the rear door weatherstrip until the screw of the rear door rear lower window frame sub-assembly is visible.
15. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here
16. REMOVE REAR DOOR QUARTER WINDOW GLASS
Click here
17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
18. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
(a) Using a T30 "TORX" socket wrench, remove the 3 screws.
*a
|
Release Plate
|
|
Remove in this Direction
|
(b) Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
(c) When reusing the rear door lock with motor assembly:
(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.
|
|
19. REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY
(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.
|
|
(b) Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.
|
Remove in this Direction
|
20. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
(a) Remove the rear door lock remote control cable assembly as shown in the illustration.
|
Remove in this Direction
|
21. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
(a) Remove the rear door inside locking cable assembly as shown in the illustration.
|
Remove in this Direction
|
|