Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014YV9
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 10/2020]
Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: ON-VEHICLE INSPECTION; 2018 - 2020 MY Camry HV [07/2017 - 10/2020]

ON-VEHICLE INSPECTION

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub sub-assembly on-vehicle inspection are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

NOTICE:

  • When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.
  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISABLE BRAKE CONTROL

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; BRAKE (FRONT): FRONT BRAKE: REMOVAL+

3. REMOVE FRONT WHEEL

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL+

4. SEPARATE FRONT FLEXIBLE HOSE

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT+

5. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT+

6. REMOVE FRONT DISC

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; BRAKE (FRONT): FRONT BRAKE: REMOVAL+

7. INSPECT FRONT AXLE HUB BEARING LOOSENESS

(a) Using a dial indicator with magnetic base, check for looseness near the center of the front axle hub sub-assembly.

Maximum Looseness:

0.05 mm (0.00196 in.)

NOTICE:

  • Ensure that the dial indicator is set perpendicular to the measurement surface.
  • Keep the magnet of the dial indicator away from the front axle hub sub-assembly and front speed sensor.

HINT:

If the looseness exceeds the maximum, replace the front axle hub sub-assembly.

8. INSPECT FRONT AXLE HUB RUNOUT

(a) Using a dial indicator with magnetic base, check for runout on the surface of the front axle hub sub-assembly outside the front axle hub bolts.

Maximum Runout:

0.05 mm (0.00196 in.)

NOTICE:

  • Ensure that the dial indicator is set perpendicular to the measurement surface.
  • Make sure to set the tip of the dial indicator towards the outside of the front axle hub bolts.
  • Keep the magnet of the dial indicator away from the front axle hub sub-assembly and front speed sensor.

HINT:

If the runout exceeds the maximum, replace the front axle hub sub-assembly.

9. INSTALL FRONT DISC

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; BRAKE (FRONT): FRONT BRAKE: INSTALLATION+

10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT+

11. INSTALL FRONT FLEXIBLE HOSE

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT+

12. INSTALL FRONT WHEEL

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; MAINTENANCE: TIRE AND WHEEL: INSTALLATION+

13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

(a) Connect the reservoir level switch connector.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; MAINTENANCE: AUXILIARY BATTERY: INSTALLATION+ 2020 - 2024 MY Camry HV [09/2019 -        ]; MAINTENANCE: AUXILIARY BATTERY: INSTALLATION+

(c) Turn the power switch on (READY).

(d) Depress the brake pedal and release it.

(e) Clear the DTCs.

Click here 2018 MY Camry HV [07/2017 - 09/2018]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: DTC CHECK / CLEAR 2019 - 2024 MY Camry HV [09/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: DTC CHECK / CLEAR