- Intelligent clearance sonar system
- Intuitive parking assist system
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014YUM |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - 10/2020] |
| Title: STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION; 2018 - 2020 MY Camry HV [07/2017 - 10/2020] | ||
INSTALLATION
PROCEDURE
1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
2. INSTALL STEERING COLUMN ASSEMBLY
NOTICE:
Make sure that the wire harness is not interfering with the steering column assembly.
(a) Install the steering column assembly with the bolt and 2 nuts.
Torque:
36 N·m {367 kgf·cm, 27 ft·lbf}
NOTICE:
- After the column is installed, check the tilt operation.
-
If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.
Tighten the nuts and check the tilt operation again.
(b) Connect each connector and engage each wire harness clamp to the steering column assembly.
3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY
|
(a) Align the matchmarks on the steering intermediate shaft assembly and steering column assembly. |
|
(b) Install the steering intermediate shaft assembly to the steering column assembly.
(c) Install the bolt.
Torque:
35 N·m {357 kgf·cm, 26 ft·lbf}
|
(d) Tighten the clamp. |
|
4. INSTALL STEERING COLUMN HOLE COVER
|
(a) Install the steering column hole cover with the 2 clips. |
|
(b) Install the clip.
(c) Return the floor carpet.
5. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
Click here
![2018 - 2024 MY Camry HV [07/2017 - ]; STEERING GEAR / LINKAGE: STEERING GEAR: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
6. INSTALL FRONT WHEEL LH
Click here
7. INSTALL NO. 1 AIR DUCT
|
(a) Engage the 3 claws to install a new No. 1 air duct. |
|
(b) Install the 2 bolts.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
8. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here
9. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
NOTICE:
- Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
- Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).
- Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.
|
(a) Using pliers, expand the clamp. |
|
(b) While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
(c) Return the clamp to its original position.
(d) Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
10. INSTALL UPPER STEERING COLUMN COVER
|
(a) Engage the 2 claws and 4 clips to connect the upper steering column cover. |
|
(b) Engage the claw to install the upper steering column cover.
|
Install in this direction |
11. INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY
|
(a) Engage the 2 claws to install the lower steering column cover sub-assembly. |
|
|
(b) Install the 3 screws. |
|
12. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
13. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Click here
14. INSTALL STEERING WHEEL ASSEMBLY
Click here
15. CHECK STEERING WHEEL CENTER POINT
16. INSTALL HORN BUTTON ASSEMBLY
Click here
17. PERFORM INITIALIZATION
|
|
|
|
Parking assist monitor system |
for Initialization:
for Calibration:
|
|
Panoramic view monitor system |
for Initialization:
for Calibration:
|
|
|