Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014YNL
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 10/2020]
Title: LIGHTING (EXT): HAZARD WARNING SWITCH: REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during hazard warning signal switch assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

PROCEDURE

1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL

2. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

3. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

4. REMOVE DEFROSTER NOZZLE ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

5. REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; METER / GAUGE / DISPLAY: HEADUP DISPLAY: REMOVAL+

6. REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

7. REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

8. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

9. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: DISASSEMBLY+

10. REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

(a) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the hazard warning signal switch assembly as shown in the illustration.

*a

Protective Tape

Remove in this Direction