Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014XM6
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: HYBRID / BATTERY CONTROL: HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY): INSTALLATION; 2018 - 2024 MY Camry HV [07/2017 -        ]

INSTALLATION

PROCEDURE

1. INSTALL HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Engage the 3 claws of the hybrid battery thermistor (sensor portions) to install the hybrid battery thermistor to the HV battery.

HINT:

Install each hybrid battery thermistor (sensor portion) to the appropriate location shown in the illustration.

*a

1st Module from the HV Battery Junction Block Assembly Side

(Wire harness color: Blue)

*b

14th Module from the HV Battery Junction Block Assembly Side

(Wire harness color: White)

*c

34th Module from the HV Battery Junction Block Assembly Side

(Wire harness color: Red)

(b) Engage the 4 clamps in the locations shown in the illustration.

*a

4th Module from the HV Battery Junction Block Assembly Side

*b

10th Module from the HV Battery Junction Block Assembly Side

*c

18th Module from the HV Battery Junction Block Assembly Side

*d

28th Module from the HV Battery Junction Block Assembly Side

(c) Connect the battery voltage sensor connector.

(d) Engage the clamp.

(e) Engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.

NOTICE:

Align each piece of tape on the wire harness of the hybrid battery thermistor with the edge of the No. 1 hybrid battery packing as shown in the illustration and then engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.

*1

No. 1 Hybrid Battery Packing

*a

Tape

*b

Hybrid Battery Thermistor Wire Harness

(f) Engage the clamp.

2. INSTALL NO. 1 HV BATTERY INTAKE DUCT LH

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Install the No. 1 HV battery intake duct LH to the HV battery with the clip.

(b) Engage the claw of hybrid battery thermistor (sensor portion) to connect the hybrid battery thermistor to the No. 1 HV battery intake duct LH.

3. INSTALL NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Pull back the rear No. 1 HV battery shield and install the No. 2 hybrid battery shield sub-assembly to the HV battery.

HINT:

Pull back the rear No. 1 HV battery shield until there is sufficient clearance for the stud bolt of the No. 2 hybrid battery shield sub-assembly.

(b) Install the 5 nuts.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

4. INSTALL HV BATTERY JUNCTION BLOCK ASSEMBLY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): INSTALLATION+

5. INSTALL UPPER HV BATTERY COVER SUB-ASSEMBLY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: BATTERY VOLTAGE SENSOR(for NICKEL METAL HYDRIDE BATTERY): INSTALLATION+

6. INSTALL HV BATTERY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for NICKEL METAL HYDRIDE BATTERY): INSTALLATION