| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014W81 |
| Model Year Start: 2018 | Model: Camry HV | Prod Date Range: [07/2017 - 10/2020] |
| Title: CRUISE CONTROL: LANE DEPARTURE ALERT SYSTEM (w/ Steering Control): Indicator Circuit; 2018 - 2020 MY Camry HV [07/2017 - 10/2020] | ||
|
Indicator Circuit |
DESCRIPTION
The forward recognition camera sends indicator illumination request signals to the combination meter assembly via CAN communication.
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (CAN BUS CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Can Bus Check.
CAN Bus Check
|
Result |
Proceed to |
|---|---|
|
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed |
A |
|
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed |
B |
| B |
|
|
|
2. |
CHECK FOR DTCs (HEALTH CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Health Check.
(e) Check DTCs.
(f) Turn the power switch off.
|
Result |
Proceed to |
|---|---|
|
No DTCs are output |
A |
|
DTCs are output |
B |
| B |
|
GO TO DTC CHART |
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM (METER DISPLAY 1) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Multi Display All (White) |
Multi-information display (White display) |
ON |
- |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Multi Display All (White) |
(f) Turn the power switch off.
|
Result |
Proceed to |
|---|---|
|
The multi-information display in the combination meter assembly turns on according to the operation of the Active Test |
A |
|
The multi-information display in the combination meter assembly does not turn on according to the operation of the Active Test |
B |
| B |
|
|
|
4. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > LKA/LDA > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
LDA Control |
Control status of lane departure alert system |
Prohibit or Permit |
Prohibit: Control prohibited Permit: Control permitted |
- |
Chassis > LKA/LDA > Data List
|
Tester Display |
|---|
|
LDA Control |
|
Result |
Proceed to |
|---|---|
|
The lane departure alert indicator illuminates and turns on according to the operation of the lane departure alert main switch |
A |
|
The lane departure alert indicator does not illuminate but the Data List item LDA Control changes according to the operation of the lane departure alert main switch |
B |
|
The lane departure alert indicator does not illuminate and the Data List item LDA Control does not change according to the operation of the lane departure alert main switch |
C |
| A |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B |
|
| C |
|
|
|