Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014W3X
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 09/2018]
Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE(for Front Door): REMOVAL; 2018 MY Camry HV [07/2017 - 09/2018]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Front door glass sub-assembly
  • Front door glass run

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry HV [07/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Click here 2018 MY Camry HV [07/2017 - 09/2018]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here 2018 MY Camry HV [07/2017 - 09/2018]; MAINTENANCE: AUXILIARY BATTERY: REMOVAL+

4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

5. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

8. REMOVE FRONT ARMREST ASSEMBLY

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

9. REMOVE COURTESY LIGHT ASSEMBLY

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; LIGHTING (INT): DOOR COURTESY LIGHT: REMOVAL+

10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

12. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

14. REMOVE FRONT DOOR PANEL PROTECTOR

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

15. REMOVE FRONT DOOR GLASS RUN

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

16. DISCONNECT FRONT DOOR WEATHERSTRIP

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; EXTERIOR PANELS / TRIM: FRONT DOOR WINDOW FRAME MOULDING: REMOVAL+

17. REMOVE DOOR FRAME GARNISH

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

18. REMOVE FRONT DOOR NO. 2 STRIPE

HINT:

When removing the front door No. 2 stripe, heat the vehicle body and front door No. 2 stripe using a heat light.

Heating Temperature

Item

Temperature

Front Door No. 2 Stripe and Vehicle Body

40 to 60°C (104 to 140°F)

CAUTION:

  • Do not touch the heat light and heated parts, touching the heat light may result in burns.
  • Touching heated parts for a long time may result in burns.

*a

Heated Part

*b

Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the front door No. 2 stripe and vehicle body.

(b) Pull back on one of the ends of the front door No. 2 stripe to remove it.

HINT:

When pulling on the front door No. 2 stripe, pull it parallel to the vehicle body.

19. REMOVE FRONT DOOR NO. 3 STRIPE

HINT:

When removing the front door No. 3 stripe, heat the vehicle body and front door No. 3 stripe using a heat light.

Heating Temperature

Item

Temperature

Front Door No. 3 Stripe and Vehicle Body

40 to 60°C (104 to 140°F)

CAUTION:

  • Do not touch the heat light and heated parts, touching the heat light may result in burns.
  • Touching heated parts for a long time may result in burns.

*a

Heated Part

*b

Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the front door No. 3 stripe and vehicle body.

(b) Pull back on one of the ends of the front door No. 3 stripe to remove it.

HINT:

When pulling on the front door No. 3 stripe, pull it parallel to the vehicle body.