Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014W3J
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 10/2020]
Title: EXTERIOR PANELS / TRIM: FRONT DOOR WINDOW FRAME MOULDING: REMOVAL; 2018 - 2020 MY Camry HV [07/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative auxiliary battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Lighting system (w/ AFS)(EXT)

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry HV [07/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry HV [07/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Front door glass sub-assembly
  • Front door glass run

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry HV [07/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL 2020 MY Camry HV [09/2019 - 10/2020]; EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL

2. REMOVE FRONT DOOR PANEL PROTECTOR

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+ 2019 MY Camry HV [09/2018 - 09/2019]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+ 2020 MY Camry HV [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

3. REMOVE FRONT DOOR GLASS RUN

Click here 2018 MY Camry HV [07/2017 - 09/2018]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+ 2019 MY Camry HV [09/2018 - 09/2019]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+ 2020 MY Camry HV [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

4. DISCONNECT FRONT DOOR WEATHERSTRIP

(a) Disengage the 2 clips and disconnect the front door weatherstrip.

5. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature

Item

Temperature

Vehicle Body

40 to 60°C (104 to 140°F)

Front Door Rear Window Frame Moulding

20 to 30°C (68 to 86°F)

CAUTION:

  • Do not touch the heat light and heated parts, touching the heat light may result in burns.
  • Touching heated parts for a long time may result in burns.

*a

Heated Part

*b

Heat Light

NOTICE:

Do not heat the vehicle body or front door rear window frame moulding excessively.

(a) Using a heat light, heat the front door rear window frame moulding.

(b) Using a moulding remover, disengage the clip and separate the double-sided tape and caulking sponge to remove the front door rear window frame moulding.

*a

Double-sided Tape

*b

Caulking Sponge

6. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

(a) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(c) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 7 rivets.

*a

Clamp

*b

Guide

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(d) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

(e) Disengage the clamp and guide to remove the front door upper window frame moulding from the door frame.