Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014VNC
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 - 09/2018]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: C1434; Steering Angle Sensor Output; 2018 MY Camry HV [07/2017 - 09/2018]

DTC

C1434

Steering Angle Sensor Output

DESCRIPTION

Steering angle sensor signals are input to the skid control ECU (brake booster with master cylinder assembly) via the CAN communication system.

HINT:

When a malfunction occurs in the communication line to the steering angle sensor, U0126 (Lost Communication With Steering Angle Sensor Module) is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.

DTCs may be stored if one of the following occurs:

  • Steering angle sensor zero point malfunction.
  • Steering angle sensor signal malfunction.
  • Steering angle sensor installation abnormality.

DTC No.

Detection Item

INF Code

DTC Detection Condition

Trouble Area

Note

C1434

Steering Angle Sensor Output

701

When communication is normal, a steering angle sensor malfunction is detected.
  • Steering angle sensor installed improperly
  • Wire harness or connector
  • Steering angle sensor

VSC DTC

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.

CHECK DTC

(a) Clear the DTCs.

Chassis > ABS/VSC/TRAC > Clear DTCs

(b) Turn the power switch off.

(c) Turn the power switch on (IG) again and check that no CAN communication system DTCs are output.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

(d) Turn the power switch on (READY).

(e) Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output.

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

DTC C1434 is output.

A

CAN communication system DTCs are output.

B

Speed sensor and/or yaw rate and acceleration sensor DTCs are output.

C

HINT:

  • If there is a malfunction in a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output even though the steering angle sensor is normal.
  • If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these malfunctions and inspect the steering angle sensor.
B

INSPECT CAN COMMUNICATION SYSTEM

C

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

A

2.

CHECK STEERING ANGLE SENSOR INSTALLATION

(a) Turn the power switch off.

(b) Check that the steering angle sensor has been installed properly.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: INSTALLATION

OK:

The steering angle sensor installation is normal.

NG

INSTALL STEERING ANGLE SENSOR CORRECTLY

OK

3.

CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Remove the steering wheel and column cover.

*a

Front view of wire harness connector

(to Steering Angle Sensor)

(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.

(c) Disconnect the K71 steering angle sensor connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K71-4 (BAT) - Body ground

Always

11 to 14 V

K71-9 (IG) - Body ground

Power switch on (IG)

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

4.

CHECK HARNESS AND CONNECTOR (GND TERMINAL)

(a) Turn the power switch off.

*a

Front view of wire harness connector

(to Steering Angle Sensor)

(b) Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering angle sensor, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K71-6 (ESS) - Body ground

1 minute after power switch off

Below 1 Ω
OK

REPLACE STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)