Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014UFU
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): P0A2A11,P0A2A15; Drive Motor "A" Temperature Sensor Circuit Short to Ground; 2018 - 2024 MY Camry HV [07/2017 -        ]

DTC

P0A2A11

Drive Motor "A" Temperature Sensor Circuit Short to Ground

DTC

P0A2A15

Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open

DTC SUMMARY

MALFUNCTION DESCRIPTION

These DTCs are stored when the motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU assembly malfunction

  • Hybrid vehicle control ECU assembly internal malfunction

Motor temperature sensor malfunction

  • Internal motor temperature sensor malfunction
  • Open or short in motor temperature sensor

Wire harness between the motor temperature sensor and hybrid vehicle control ECU assembly

  • The connectors are not connected properly
  • Foreign matter or water on the connector terminals
  • Open or short in wire harness

HINT:

If any of these DTCs are stored, the motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the motor (MG2) becomes high. If the self-protection function does not operate, the motor (MG2) may malfunction and cause the vehicle to enter fail-safe mode.

DESCRIPTION

The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in the motor (MG2) temperature. The lower the motor (MG2) temperature, the higher the thermistor resistance. Conversely, the higher the motor (MG2) temperature, the lower the resistance.

HINT:

The term "drive motor A" indicates the motor (MG2).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P0A2A11

Drive Motor "A" Temperature Sensor Circuit Short to Ground

Short to ground in the motor temperature sensor circuit

(1 trip detection logic)
  • Wire harness or connector
  • Hybrid vehicle control ECU assembly
  • Motor temperature sensor (Hybrid vehicle transaxle assembly)

Comes on

Master Warning Light:

Comes on

P0A2A15

Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open

Open or short to +B in the motor temperature sensor circuit

(1 trip detection logic)
  • Wire harness or connector
  • Hybrid vehicle control ECU assembly
  • Motor temperature sensor (Hybrid vehicle transaxle assembly)

Comes on

Master Warning Light:

Comes on

Related Data List

DTC No.

Data List

P0A2A11

Motor Temperature

P0A2A15

HINT:

After confirming that DTC P0A2A11 or P0A2A15 is output, use the Techstream to check "Motor Temperature" in the Data List.

Displayed Temperature

Malfunction

-40°C (-40°F)

Open circuit or short to +B

215°C (419°F)

Short to ground

MONITOR DESCRIPTION

If the hybrid vehicle control ECU assembly detects a malfunction of the motor temperature sensor, it will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Related DTCs

P0A2C (INF P0A2A11): Drive Motor "A" Temperature Sensor Circuit Low

P0A2D (INF P0A2A15): Drive Motor "A" Temperature Sensor Circuit High

Required sensors/components

Motor temperature sensor

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

1 driving cycle

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Hybrid vehicle control ECU assembly

DTC P0A2C (INF P0A2A11) is not detected

DTC P0A2D (INF P0A2A15) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): UTILITY

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2018 - 2022 MY Camry HV [07/2017 - 08/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): DTC CHECK / CLEAR 2023 - 2024 MY Camry HV [08/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 2 minutes or more.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. With power switch on (IG) and wait for 5 seconds or more.[*1]

    HINT:

    [*1] : Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

WIRING DIAGRAM

PROCEDURE

1.

CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

(a) Check the connection condition of the hybrid vehicle control ECU assembly connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.

Result:

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C
B

CONNECT SECURELY
C

REPAIR OR REPLACE HARNESS OR CONNECTOR
A

2.

CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

(a) Check that the intermediate connector which connects the motor temperature sensor to the hybrid vehicle control ECU assembly is securely connected with no deformation, and that there is no contamination by water or foreign matter.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

For vehicles in which the intermediate connector is inside the relay block, check for signs of water intrusion inside the relay block.

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C
B

CONNECT SECURELY
C

REPAIR OR REPLACE HARNESS OR CONNECTOR
A

3.

CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

(a) Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C
B

CONNECT SECURELY
C

REPAIR OR REPLACE HARNESS OR CONNECTOR
A

4.

READ VALUE USING TECHSTREAM (MOTOR TEMPERATURE)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temperature.

Powertrain > Hybrid Control > Data List

Tester Display

Motor Temperature

(d) Read the Data List.

Result

Proceed to

-40°C (-40°F)

A

215°C (419°F)

B

Same as actual temperature

C

(e) Turn the power switch off.

B

GO TO STEP 7

C

REPAIR OR REPLACE HARNESS OR CONNECTOR
A

5.

INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

(a) Disconnect the C65 motor temperature sensor connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (MMT) - 2 (MMTG)

Power switch off

0.3443 to 1446 kΩ

HINT:

Terminal No. 3 on the component side connector is empty.

*a

Component without harness connected

(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))

(c) Reconnect the C65 motor temperature sensor connector.

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL

OK

6.

INSPECT HYBRID VEHICLE CONTROL ECU ASSEMBLY

(a) Connect terminals 24 (MMT) and 23 (MMTG) of the A28 hybrid vehicle control ECU assembly connector.

*a

Component with harness connected

(Hybrid Vehicle Control ECU Assembly)

(b) Connect the Techstream to the DLC3.

(c) Turn the power switch on (IG).

(d) Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temperature.

Powertrain > Hybrid Control > Data List

Tester Display

Motor Temperature

(e) Read the Data List.

OK:

Techstream Display

Condition

Specified Condition

Motor Temperature

Terminals A28-24 (MMT) and A28-23 (MMTG) connected

Power switch on (IG)

215°C (419°F)

(f) Turn the power switch off.

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

7.

INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

(a) Disconnect the C65 motor temperature sensor connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (MMT) - 2 (MMTG)

Power switch off

0.3443 to 1446 kΩ

HINT:

Terminal No. 3 on the component side connector is empty.

*a

Component without harness connected

(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))

(c) Reconnect the C65 motor temperature sensor connector.

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL

OK

8.

CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

(a) Disconnect the C65 motor temperature sensor connector.

(b) Disconnect the A28 hybrid vehicle control ECU assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):

Tester Connection

Condition

Specified Condition

C65-1 (MMT) - A28-24 (MMT)

Power switch off

Below 1 Ω

C65-2 (MMTG) - A28-23 (MMTG)

Power switch off

Below 1 Ω

Standard Resistance (Check for Short):

Tester Connection

Condition

Specified Condition

C65-1 (MMT) or A28-24 (MMT) - Body ground and other terminals

Power switch off

10 kΩ or higher

C65-2 (MMTG) or A28-23 (MMTG) - Body ground and other terminals

Power switch off

10 kΩ or higher

*a

Front view of wire harness connector

(to Motor Temperature Sensor)

*b

Rear view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

(d) Reconnect the A28 hybrid vehicle control ECU assembly connector.

(e) Reconnect the C65 motor temperature sensor connector.

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR