Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014U4P
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: NETWORKING: CAN COMMUNICATION SYSTEM: Certification ECU Communication Stop Mode; 2018 - 2024 MY Camry HV [07/2017 -        ]

Certification ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Certification ECU Communication Stop Mode

Any of the following conditions are met:

  • Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the Techstream.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE 2020 MY Camry HV [09/2019 - 10/2020]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE

  • Communication stop history for "Certification (Smart)" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Certification (Smart)" is 6 or more.)

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE 2020 MY Camry HV [09/2019 - 10/2020]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: PROBLEM SYMPTOMS TABLE

  • Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here 2018 MY Camry HV [07/2017 - 09/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DTC COMBINATION TABLE 2019 MY Camry HV [09/2018 - 09/2019]; NETWORKING: CAN COMMUNICATION SYSTEM: DTC COMBINATION TABLE 2020 MY Camry HV [09/2019 - 10/2020]; NETWORKING: CAN COMMUNICATION SYSTEM: DTC COMBINATION TABLE 2021 - 2024 MY Camry HV [10/2020 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: DTC COMBINATION TABLE

  • Certification ECU (smart key ECU assembly) branch line or connector
  • Power source circuit of certification ECU (smart key ECU assembly)
  • Certification ECU (smart key ECU assembly) ground circuit
  • Certification ECU (smart key ECU assembly)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry HV [09/2019 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here 2018 MY Camry HV [07/2017 - 09/2018]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2019 MY Camry HV [09/2018 - 09/2019]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2020 MY Camry HV [09/2019 - 10/2020]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2021 MY Camry HV [10/2020 - 08/2021]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2022 - 2024 MY Camry HV [08/2021 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry HV [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the K62 certification ECU (smart key ECU assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K62-1 (CANH) - K62-2 (CANL)

Cable disconnected from negative (-) auxiliary battery terminal

54 to 69 Ω

*a

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly))

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

K62-18 (E) - Body ground

Cable disconnected from negative (-) auxiliary battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly))

(b) Reconnect the cable to the negative (-) auxiliary battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

K62-4 (+B) - Body ground

Power switch off

11 to 14 V

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)