Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014TYW
Model Year Start: 2018 Model: Camry HV Prod Date Range: [07/2017 -           ]
Title: NETWORKING: LIN COMMUNICATION SYSTEM: B2324; Rear Door LH ECU Communication Stop; 2018 - 2024 MY Camry HV [07/2017 -        ]

DTC

B2324

Rear Door LH ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2324

Rear Door LH ECU Communication Stop

No communication between power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Main body ECU (multiplex network body ECU)
  • Instrument panel junction block assembly
  • Power window regulator motor assembly (rear LH door)
  • Wire harness or connector
  • DOOR R/L fuse

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

    Click here 2018 - 2024 MY Camry HV [07/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here 2018 - 2019 MY Camry HV [07/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry HV [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry HV [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

PROCEDURE

1.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Remove the instrument panel junction block assembly.

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)

-

-

(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

(c) Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

Standard Resistance:

Tester Connection

Condition

Specified Condition

3D-25 - MB-16 (LIN2)

Always

Below 1 Ω

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

OK

2.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

(a) Disconnect the Q6 power window regulator motor assembly (rear LH door) connector.

(b) Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3D-25 - Q6-9 (LIN)

Power switch off

Below 1 Ω

Q6-9 (LIN) or 3D-25 - Body ground

Power switch off

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY, BODY GROUND)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

Q6-2 (B) - Q6-1 (GND)

Power switch off

11 to 14 V

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Q6-1 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

(a) Replace the power window regulator motor assembly (rear LH door).

Click here 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR (for Rear Door): REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR (for Rear Door): REMOVAL

NEXT

5.

CHECK FOR DTC

(a) Clear the DTCs.

Body Electrical > Main Body > Clear DTCs

(b) Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes

OK:

DTC B2324 is not output.

OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2018 - 2020 MY Camry HV [07/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry HV [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL