2GR-FKS (ENGINE MECHANICAL): FRONT CRANKSHAFT OIL SEAL: REMOVAL; 2023 - 2024 MY Camry [08/2022

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM10000000262T4
Model Year Start: 2023	Model: Camry	Prod Date Range: [08/2022 - ]
Title: 2GR-FKS (ENGINE MECHANICAL): FRONT CRANKSHAFT OIL SEAL: REMOVAL; 2023 - 2024 MY Camry [08/2022 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
*1: When the ECM is replaced with a new one, reset memory is unnecessary.
Battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane Tracing Assist System
	Perform steering sensor zero point calibration	Pre-collision System
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic view monitor system
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
Replacement of ECM	ECU communication ID registration (Immobiliser system)	Engine start function
Gas leak from exhaust system is repaired	Inspection After Repair	Poor idle, etc. Engine start function, etc.
Replacement of automatic transaxle assembly	Reset memory Input transaxle compensation code into ECM Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization for Registration
Replacement of ECM (If possible, read the transaxle compensation code from the previous ECM)	Reset memory*1 Transfer transaxle compensation code Perform road test to allow ECM to learn
Replacement of ECM (If impossible, read the transaxle compensation code from the previous ECM)	Reset memory*1 Reset transaxle compensation code Perform road test to allow ECM to learn
Replacement of ECM	Code registration	Wireless door lock control system Smart key system (for Entry Function) Smart key system (for Start Function)
Replacement of automatic transaxle fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Rear television camera assembly optical axis (Back camera position setting)	Parking assist monitor system	for Initialization for Calibration
Replacement of front bumper assembly	Front television camera view adjustment	Panoramic view monitor system	for Initialization for Calibration
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Television camera controller initialization Adjust steering angle Rear television camera assembly optical axis (Back camera position setting)	Panoramic view monitor system	for Initialization for Calibration
Front wheel alignment adjustment	Perform "Reset Memory" Perform acceleration sensor zero point calibration and system information memorization	VSC disabled or malfunctioning DTCs are output Slip indicator light illuminated ABS warning light illuminated

PROCEDURE

1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Click here

2. REMOVE V-RIBBED BELT

Click here

3. REMOVE CRANKSHAFT PULLEY

(a) Using SST to hold the crankshaft pulley, loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads remain screwed into the crankshaft.

*a	Hold
	Turn

SST: 09213-70011

09213-70020

SST: 09330-00021

(b) Using SST, remove the crankshaft pulley set bolt and crankshaft pulley.

*a	Hold
	Turn

SST: 09950-50013

09951-05010

09952-05010

09953-05020

09954-05021

4. REMOVE TIMING CHAIN CASE OIL SEAL

(a) Using a screwdriver with its tip wrapped with protective tape, pry out the timing chain case oil seal.

NOTICE:

After removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.

*a	Protective Tape