Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000249GV
Model Year Start: 2023 Model: Camry Prod Date Range: [08/2022 -           ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): Additional Key cannot be Registered; 2023 - 2024 MY Camry [08/2022 -        ]

Additional Key cannot be Registered

DESCRIPTION

If additional registration is not possible, a malfunction of the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly), engine switch, No. 1 indoor electrical key antenna assembly (front floor) or door control receiver is suspected.

CAUTION / NOTICE / HINT

NOTICE:

  • If registration of an electrical key transmitter sub-assembly cannot be performed, refer to Registration.

    Click here 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING

  • When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Precaution.
  • After repair, confirm that no DTCs are output.

HINT:

When additional registration is not possible, freeze frame data may be stored in the certification ECU (smart key ECU assembly).

If freeze frame data is available, it can be helpful in determining whether any parts were malfunctioning or not or narrowing down the suspected areas based on the table below.

Registration Function (Reason for Non-operation)

Parameter Name

Cause of Problem and Countermeasure

Failed Registration Mode

Make sure that another mode or a different registration mode is not selected, and then perform registration again.

Key Registration Max

Registration was not possible because the maximum number of the electrical key transmitter sub-assemblies has already been registered to the certification ECU (smart key ECU assembly).

If a new electrical key transmitter sub-assembly needs to be registered, such as when one of the registered electrical key transmitter sub-assemblies has been lost, erase an unnecessary ID code first.

Key Verification: Amp Abnormal

Although a registered electrical key transmitter sub-assembly was held near the engine switch, electrical key transmitter sub-assembly registration could not be confirmed due to a malfunction of the immobiliser amplifier, such as a short to ground. DTC B278A or B2784 was stored.

Key Verification: Read Error

A registered electrical key transmitter sub-assembly was not held near the engine switch properly or electrical key transmitter sub-assembly registration cannot be confirmed due to wave interference, etc.

Register the electrical key transmitter sub-assembly using the correct procedure or use another registered electrical key transmitter sub-assembly.

Transponder Key Amp Abnormal

Although an unregistered electrical key transmitter sub-assembly was held near the engine switch, electrical key transmitter sub-assembly registration cannot be completed due to a malfunction of the immobiliser amplifier, such as a short to ground. DTC B278A or B2784 was stored.

New Key Registration Error

An unregistered electrical key transmitter sub-assembly was not held near the engine switch properly or electrical key transmitter sub-assembly registration cannot be confirmed due to a malfunction, such as wave interference.

Reregister the electrical key transmitter sub-assembly using the correct procedure or use another registered electrical key transmitter sub-assembly.

New Key Vehicle ID Error

Although the vehicle ID stored in the certification ECU (smart key ECU assembly) should be registered to the electrical key transmitter sub-assembly during electrical key transmitter sub-assembly registration, it was not successful.

Use another unregistered electrical key transmitter sub-assembly for registration.

New Key Registration Failed

Although an unregistered electrical key transmitter sub-assembly was held near the engine switch for registration, electrical key transmitter sub-assembly registration was not successful due to wave interference (such as radio waves emitted from a device in the cabin) or a low transmitter battery.

New Key Already Registered

As a registered electrical key transmitter sub-assembly was held near the engine switch by mistake, electrical key transmitter sub-assembly registration was not successful.

Using an unregistered electrical key transmitter sub-assembly, perform the registration procedure again.

New Key ID Code Error

Replace the certification ECU (smart key ECU assembly).

New Key Information Abnormal

The ID code of an electrical key transmitter sub-assembly could not be registered to the certification ECU (smart key ECU assembly). If 2 electrical key transmitter sub-assemblies are held near the engine switch at the same time, incorrect registration information will be stored in the certification ECU (smart key ECU assembly), suspending registration.

Reregister the electrical key transmitter sub-assembly using the correct registration procedure.

Body Electrical > Smart Key > Utility

Tester Display

Operation History

PROCEDURE

1.

CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Smart Key > Trouble Codes

NOTICE:

If a malfunction occurs, do not remove/install the vehicle auxiliary battery before checking for DTCs.

OK:

DTCs are not output.

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

OK

2.

READ VALUE USING TECHSTREAM (UNMATCHED VEHICLE-ID)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG)

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Unmatched Vehicle-ID

Key No. (incorrect or correct)

No or Yes

No: Communication normal

Yes: Communication malfunction

The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).

Other potential causes:

  • An electrical key transmitter sub-assembly from a different vehicle is being used.
  • A communication error due to wave interference.
  • The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.

Body Electrical > Smart Key > Data List

Tester Display

Unmatched Vehicle-ID

Result

Proceed to

"No" is displayed

A

"Yes" is displayed

B

B

GO TO STEP 4

A

3.

CHECK SMART KEY SYSTEM (for Start Function)

(a) Remove the transmitter battery from the electrical key transmitter sub-assembly.

(b) With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.

OK:

The power source mode changes.

HINT:

If the power source mode changes, the cabin verification is malfunctioning.

*1

Engine Switch

*2

Electrical Key Transmitter Sub-assembly

Result

Proceed to

The power source mode changes

A

The power source mode does not change

B

B

GO TO SMART KEY SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

A

4.

REGISTRATION

(a) Using an unregistered electrical key transmitter sub-assembly, perform the additional registration procedure.

Click here 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

OK:

Additional registration can be completed.

OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (FIRST REGISTERED KEY WAS DEFECTIVE)

NG

5.

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Temporarily replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies.

HINT:

  • For replacement.

    Click here 2021 - 2024 MY Camry [10/2020 -        ]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

  • For registration.

    Click here 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

OK:

All of the electrical key transmitter sub-assemblies could be registered to the new certification ECU (smart key ECU assembly) successfully.

OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

GO TO OTHER PROBLEM (New key cannot be Registered)