THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): TERMINALS OF ECU; 2023 - 2024 MY Camry [08/2022

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM10000000249F7
Model Year Start: 2023	Model: Camry	Prod Date Range: [08/2022 - ]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): TERMINALS OF ECU; 2023 - 2024 MY Camry [08/2022 - ]

TERMINALS OF ECU

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect the A13, R8 and K62 certification ECU (smart key ECU assembly) connectors.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Tester Connection	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
A13-16 (NE) - Body ground	B - Body ground	Input	Engine speed signal	Always	10 kΩ or higher	Engine/EV System Condition
R8-25 (STP1) - Body ground	BE - Body ground	Input	Stop light switch signal	Brake pedal depressed → Brake pedal released	9 V or higher → 1 V or less	Stop Light Switch1
K62-4 (+B) - K62-18 (E)	W - W-B	Input	Power source	Always	11 to 14 V	-
K62-22 (P) - K62-18 (E)	R - W-B	Input	P position signal	Shift lever in P → Shift lever not in P	30 kΩ or higher → Below 200 Ω	Shift P Signal
K62-15 (CUTB) - Body ground	R - Body ground	Input	Dark current cut pin*	Always	11 to 14 V	-
K62-18 (E) - Body ground	W-B - Body ground	-	GND	Always	Below 1 Ω	-
K62-14 (SLP) - Body ground	W-B - Body ground	-	GND	Always	Below 1 Ω	-
K62-21 (SSW2) - Body ground	L - Body ground	Input	SSW2 contact signal HINT: Backup for SSW1. Behaves the same way as SSW1.	Engine switch pushed → Engine switch not pushed	Below 15 Ω → 10 kΩ or higher	Start Switch2
K62-23 (SSW1) - Body ground	GR - Body ground	Input	SSW1 contact signal	Engine switch pushed → Engine switch not pushed	Below 15 Ω → 10 kΩ or higher	Start Switch1
K62-19 (SPD) - Body ground	R - Body ground	Input	Vehicle speed signal	Always	30 kΩ or higher	Vehicle Speed Signal

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).

(d) Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Tester Connection	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
A13-20 (STA) - K62-18 (E)	L - W-B	Input	When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started".	Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)	6 V or higher*2 → 1.0 V or less	-
A13-9 (STAR) - K62-18 (E)	P - W-B	Input / Output	Outputs voltage to the starter relay Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 1000 rpm.) HINT: When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.	Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)	6 V or higher*2 → 1.0 V or less	-
A13-9 (STAR) - K62-18 (E)	P - W-B	Input / Output	Receives neutral start switch (P, N position detection) signal Monitors whether the neutral start switch is on (P or N) or off (other than P or N). Applies voltage via a resistor (large) in the certification ECU (smart key ECU assembly). When the neutral start switch is on, due to the starter relay coil resistance (small) using some of the voltage, the voltage at terminal STAR will be low (2.7 V or less), and when the neutral start switch is off, the voltage will be high (9 V or more).	Perform the following operations except while the engine is cranking: Shift lever in any position other than P or N → Shift lever in P or N (at 20°C (68°F))	9 V or higher → 2.7 V or less	Neutral SW/ Clutch SW
A13-16 (NE) - K62-18 (E)	B - W-B	Input	Engine speed signal	Idling (engine warmed up)	Pulse generation (See waveform 1)	Engine/EV System Condition
R8-25 (STP1) - K62-18 (E)	BE - W-B	Input	Stop light switch signal	Brake pedal released → Brake pedal depressed	1 V or less → 9 V or higher	Stop Light Switch1
K62-13 (LIN) - K62-18 (E)	GR - W-B	Input / Output	LIN communication line	Engine switch on (IG)	Pulse generation	-
K62-22 (P) - K62-18 (E)	R - W-B	Input	P position signal	Shift lever in P → Shift lever not in P	9 V or higher → 2.76 V or less	Shift P Signal
K62-21 (SSW2) - K62-18 (E)	L - W-B	Input	SSW2 contact signal HINT: Backup for SSW1. Behaves the same way as SSW1.	Engine switch not pushed → Engine switch pushed	9 V or higher → 1 V or less	Start Switch2
K62-23 (SSW1) - K62-18 (E)	GR - W-B	Input	SSW1 contact signal	Engine switch not pushed → Engine switch pushed	9 V or higher → 1 V or less	Start Switch1
K62-16 (ACCD) - K62-18 (E)	LG - W-B	Output	ACC signal	Engine switch off → Engine switch on (ACC)	1 V or less → 8.5 V or higher	ACC Relay Monitor
K62-17 (IG1D) - K62-18 (E)	R - W-B	Output	IG signal	Engine switch on (ACC) → Engine switch on (IG)	1 V or less → 9 V or higher	IG Relay Monitor (Outside)
K62-19 (SPD) - K62-18 (E)	R - W-B	Input	Vehicle speed signal	Vehicle being driven at approx. 5 km/h (3 mph)	Pulse generation (See waveform 2)	Vehicle Speed Signal
K62-8 (CLG5) - K62-18 (E)	B - W-B	Output	Output to No. 1 indoor electrical key antenna assembly (front floor)	Procedure: Engine switch off Electrical key transmitter sub-assembly not inside vehicle Within 30 seconds of closing any door	Pulse generation (See waveform 3)	-
K62-9 (CG5B) - K62-18 (E)	LG - W-B	Output	Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal)	Procedure: Engine switch off Electrical key transmitter sub-assembly not inside vehicle Within 30 seconds of closing any door	Pulse generation (See waveform 3)	-
R8-5 (CLG6) - K62-18 (E)	W - W-B	Output	Output to No. 1 indoor electrical key antenna assembly (rear floor)	Procedure: Engine switch off Electrical key transmitter sub-assembly not inside vehicle Within 30 seconds of closing any door	Pulse generation (See waveform 3)	-
R8-6 (CG6B) - K62-18 (E)	R - W-B	Output	Output to No. 1 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal)	Procedure: Engine switch off Electrical key transmitter sub-assembly not inside vehicle Within 30 seconds of closing any door	Pulse generation (See waveform 3)	-
K62-5 (TXCT) - K62-11 (AGND)	GR - BE	Output	Signal output to transponder key amplifier	Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed	Below 1 V	BCC Malfunction Abnormal Status Different Encrypt Code Different Serial Number Frame Error Response
K62-6 (CODE) - K62-11 (AGND)	B - BE	Input	Signal input from transponder key amplifier	Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed	Below 1 V
K62-7 (VC5) - K62-11 (AGND)	BE - BE	Output	Transponder key amplifier power supply	Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed	Below 1 V
K62-11 (AGND) - Body ground	BE - Body ground	-	Transponder key amplifier ground	Always	Below 1 Ω
K62-5 (TXCT) - K62-11 (AGND)	GR - BE	Output	Signal output to transponder key amplifier (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)	Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed	Pulse generation (See waveform 4)	BCC Malfunction Abnormal Status Different Encrypt Code Different Serial Number Frame Error Response
K62-6 (CODE) - K62-11 (AGND)	B - BE	Input	Signal input from transponder key amplifier (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))	Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch HINT: Remove the transmitter battery before performing this inspection.	Pulse generation (See waveform 5)
K62-7 (VC5) - K62-11 (AGND)	BE - BE	Output	Transponder key amplifier power supply (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)	Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed	Pulse generation (See waveform 6)
K62-20 (IND) - K62-18 (E)	W - W-B	Output	Security indicator output	Engine switch off → on (IG)	Pulse generation → Below 2 V	-
R8-7 (WCSW) - K62-18 (E)*1	LG - W-B	Output	Wireless charger system stop signal	Procedure: Engine switch off Electrical key transmitter sub-assembly inside vehicle Engine switch off → on (ACC)	Below 1 V → 4.5 to 6 V (For 1 second after engine switch on (ACC))	-

*1: w/ Wireless Charging System

HINT:

*2: While the engine is cranking, the battery voltage may drop to approximately 6 V.

(e) Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1

Measurement Condition

Item	Content
Tester Connection	A13-16 (NE) - K62-18 (E)
Tool Setting	2 V/DIV., 2 ms./DIV.
Condition	Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.

(2) Waveform 2

Measurement Condition

Item	Content
Tester Connection	K62-19 (SPD) - K62-18(E)
Tool Setting	5 V/DIV., 20 ms./DIV.
Condition	Vehicle being driven at approx. 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.

(3) Waveform 3

*a	For 30 seconds after any door closed
*b	After 30 seconds or more have elapsed since any door closed

Measurement Condition

Item

Content

Tester Connection

K62-8 (CLG5) - K62-18 (E)

K62-9 (CG5B) - K62-18 (E)

R8-5 (CLG6) - K62-18 (E)

R8-6 (CG6B) - K62-18 (E)

Tool Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

Engine switch off
Electrical key transmitter sub-assembly not inside vehicle
Within 30 seconds of closing any door

(4) Waveform 4

Measurement Condition

Item	Content
Tester Connection	K62-5 (TXCT) - K62-11 (AGND)
Tool Setting	2 V/DIV., 20 ms./DIV.
Condition	Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed

(5) Waveform 5

*a	Waveform
*b	Waveform (detail)

Measurement Condition

Item	Content
Tester Connection	K62-6 (CODE) - K62-11 (AGND)
Tool Setting	Waveform 1 V/DIV., 20 ms./DIV. Waveform (detail) 2 V/DIV., 100 μs./DIV.
Condition	Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.

(6) Waveform 6

Measurement Condition

Item	Content
Tester Connection	K62-7 (VC5) - K62-11 (AGND)
Tool Setting	2 V/DIV., 200 ms./DIV.
Condition	Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed

CHECK ID CODE BOX (IMMOBILISER CODE ECU)

(a) Disconnect the K152 ID code box (immobiliser code ECU) connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.

Tester Connection	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
K152-1 (+B) - Body ground	LA-GR - Body ground	Input	Power source	Engine switch off	11 to 14 V	-
K152-5 (GND) - Body ground	W-B - Body ground	-	Ground	Always	Below 1 Ω	-

(d) Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
K152-3 (EFII) - K152-5 (GND)	LG - W-B	Input	EFI communication input(Signal input from engine to ID code box (immobiliser code ECU))	Engine switch off	11 to 14 V	Smart Key EFI/EV Code Receive Engine/System Start Request
K152-3 (EFII) - K152-5 (GND)	LG - W-B	Input	EFI communication input(Signal input from engine to ID code box (immobiliser code ECU))	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery	Pulse generation (See waveform 1)
K152-4 (EFIO) - K152-5 (GND)	L - W-B	Output	EFI communication output(Signal output from ID code box (immobiliser code ECU) to engine)	Engine switch off	Below 1 V
K152-4 (EFIO) - K152-5 (GND)	L - W-B	Output	EFI communication output(Signal output from ID code box (immobiliser code ECU) to engine)	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery	Pulse generation (See waveform 2)
K152-2 (LIN1) - K152-5 (GND)	GR - W-B	Input / Output	LIN communication line	Engine switch on (IG)	Pulse generation	-

(e) Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1

Approximately 160 ms.

Approximately 270 ms.

Measurement Condition

Item	Content
Tester Connection	K152-3 (EFII) - K152-5 (GND)
Tool Setting	2 V/DIV., 500 ms./DIV.
Condition	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery

(2) Waveform 2

Approximately 160 ms.

Approximately 270 ms.

Measurement Condition

Item	Content
Tester Connection	K152-4 (EFIO) - K152-5 (GND)
Tool Setting	2 V/DIV., 500 ms./DIV.
Condition	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery

CHECK ECM (for A25A-FKS)

(a) Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
A24-35 (+B2) - A24-10 (E1)	L - W-B	Input	Ignition power supply	Engine switch on (IG)	11 to 14 V	-
A24-9 (+B) - A24-10 (E1)	L - W-B	Input	Ignition power supply	Engine switch on (IG)	11 to 14 V	-
A24-15 (MREL) - A24-10 (E1)	W - W-B	Input	Ignition power supply	Engine switch on (IG)	11 to 14 V	-
A24-1 (BATT) - A24-10 (E1)	G - W-B	Input	+B power supply	Always	11 to 14 V	-
A24-10 (E1) - Body ground	W-B - Body ground	-	Ground	Always	Below 1 Ω	-
A24-36 (E2) - Body ground	W-B - Body ground	-	Ground	Always	Below 1 Ω	-
A24-25 (IMO) - A24-10 (E1)	V - W-B	Output	Certification ECU (smart key ECU assembly) communication output	Engine switch off	11 to 14 V	-
A24-25 (IMO) - A24-10 (E1)	V - W-B	Output	Certification ECU (smart key ECU assembly) communication output	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery	Pulse generation (See waveform 1)	-
A24-26 (IMI) - A24-10 (E1)	GR - W-B	Input	Certification ECU (smart key ECU assembly) communication input	Engine switch off	11 to 14 V → 1 V or less	-
A24-26 (IMI) - A24-10 (E1)	GR - W-B	Input	Certification ECU (smart key ECU assembly) communication input	Engine switch turned on (IG) using registered electrical key transmitter sub-assembly	Pulse generation (See waveform 2)	-

(b) Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

Approximately 160 ms.

Approximately 270 ms.

Measurement Condition

Item	Content
Tester Connection	A24-25 (IMO) - A24-10 (E1)
Tool Setting	2 V/DIV., 500 ms./DIV.
Condition	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery

(2) Waveform 2 (Reference)

Approximately 160 ms.

Approximately 270 ms.

Measurement Condition

Item	Content
Tester Connection	A24-26 (IMI) - A24-10 (E1)
Tool Setting	2 V/DIV., 500 ms./DIV.
Condition	Engine switch turned on (IG) using registered electrical key transmitter sub-assembly

CHECK ECM (for 2GR-FKS)

(a) Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
A21-3 (+B2) - C96-53 (E1)	L - W-B	Input	Ignition power supply	Engine switch on (IG)	11 to 14 V	-
A21-2 (+B) - C96-53 (E1)	L - W-B	Input	Ignition power supply	Engine switch on (IG)	11 to 14 V	-
A21-46 (MREL) - C96-53 (E1)	W - W-B	Input	Ignition power supply	Engine switch on (IG)	11 to 14 V	-
A21-1 (BATT) - C96-53 (E1)	R - W-B	Input	+B power supply	Always	11 to 14 V	-
C96-53 (E1) - Body ground	W-B - Body ground	-	Ground	Always	Below 1 Ω	-
A21-45 (IMO) - C96-53 (E1)	V - W-B	Output	Certification ECU (smart key ECU assembly) communication output	Engine switch off	11 to 14 V	-
A21-45 (IMO) - C96-53 (E1)	V - W-B	Output	Certification ECU (smart key ECU assembly) communication output	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery	Pulse generation (See waveform 1)	-
A21-59 (IMI) - C96-53 (E1)	GR - W-B	Input	Certification ECU (smart key ECU assembly) communication input	Engine switch off	11 to 14 V → 1 V or less	-
A21-59 (IMI) - C96-53 (E1)	GR - W-B	Input	Certification ECU (smart key ECU assembly) communication input	Engine switch turned on (IG) using registered electrical key transmitter sub-assembly	Pulse generation (See waveform 2)	-

(b) Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

Approximately 160 ms.

Approximately 270 ms.

Measurement Condition

Item	Content
Tester Connection	A21-45 (IMO) - C96-53 (E1)
Tool Setting	2 V/DIV., 500 ms./DIV.
Condition	Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery

(2) Waveform 2 (Reference)

Approximately 160 ms.

Approximately 270 ms.

Measurement Condition

Item	Content
Tester Connection	A21-59 (IMI) - C96-53 (E1)
Tool Setting	2 V/DIV., 500 ms./DIV.
Condition	Engine switch turned on (IG) using registered electrical key transmitter sub-assembly

CHECK ENGINE SWITCH

(a) Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol)	Wiring Color	Input / Output	Terminal Description	Condition	Specified Condition	Related Data List Item/DTC
K63-6 (AGND) - Body ground	BE - Body ground	-	Transponder key amplifier ground	Always	Below 1 Ω	-
K63-7 (TXCT) - K63-6 (AGND)	GR - BE	Input	Immobiliser communication input	Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed	Below 1 V	-
K63-8 (CODE) - K63-6 (AGND)	B - BE	Output	Immobiliser communication output	Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed	Below 1 V	-
K63-10 (VC5) - K63-6 (AGND)	BE - BE	Input	Transponder key amplifier power supply	Engine switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed	Below 1 V	-

(b) Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Wiring Color

Input / Output

Terminal Description

Condition

Specified Condition

Related Data List Item/DTC

K63-7 (TXCT) - K63-6 (AGND)

GR - BE

Input

Signal input from certification ECU (smart key ECU assembly)

(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)

Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed

Pulse generation

(See waveform 1)

BCC Malfunction
Abnormal Status
Different Encrypt Code
Different Serial Number
Frame Error
Response
HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above

K63-8 (CODE) - K63-6 (AGND)

B - BE

Output

Signal output to certification ECU (smart key ECU assembly)

(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))

Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch*

Pulse generation

(See waveform 2)

K63-10 (VC5) - K63-6 (AGND)

BE - BE

Input

Transponder key amplifier power supply

(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)

Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed

Pulse generation

(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

Measurement Condition

Item	Content
Tester Connection	K63-7 (TXCT) - K63-6 (AGND)
Tool Setting	2 V/DIV., 20 ms./DIV.
Condition	Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed

(2) Waveform 2 (Reference)

*a	Waveform
*b	Waveform (detail)

Measurement Condition

Item	Content
Tester Connection	K63-8 (CODE) - K63-6 (AGND)
Tool Setting	Waveform 1 V/DIV., 20 ms./DIV. Waveform (detail) 2 V/DIV., 100 μs./DIV.
Condition	Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.

(3) Waveform 3 (Reference)

Measurement Condition

Item	Content
Tester Connection	K63-10 (VC5) - K63-6 (AGND)
Tool Setting	2 V/DIV., 200 ms./DIV.
Condition	Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed

TERMINALS OF ECU

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Smart Key

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition

Measurement Condition