INSTALLATION

PROCEDURE

1. INSTALL ROOF HEADLINING ASSEMBLY

(a) Install the 2 clips to the roof headlining assembly.

*a Clip (Black) *b Clip (White)

(b) Put the roof headlining assembly into the vehicle through the front door RH as shown in the illustration.

Install in this Direction

-

-

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.

(c) for Roof Side (for Normal Roof):

(1) Engage the 2 claws to install the base of each visor holder.

(2) Engage the 2 clips and install the roof headlining assembly with the 2 clips.

(d) for Roof Side (for Moon Roof):

(1) Engage the 2 claws to install the base of each visor holder.

(2) Engage the 2 clips and install the roof headlining assembly with the 2 clips.

(3) Connect the connector.

(e) for Roof Side (for Panoramic Moon Roof):

(1) Engage the guide and 14 fasteners.

(2) Engage the 2 claws to install the base of each visor holder.

(3) Engage the 2 clips and install the roof headlining assembly with the 2 clips.

(4) Connect the connector.

(f) for Rear Pillar LH Side:

(1) Engage the clamp.

(2) Connect the connector.

(g) for Rear Pillar RH Side:

(1) Engage each clamp.

(2) Connect each connector.

(h) for Front Pillar LH Side:

(1) Remove the protective cover.

(2) Engage the 4 clamps.

(3) Connect each connector.

(4) Install the protective cover.

(i) for Front Pillar RH Side:

(1) Remove the protective cover.

(2) Engage the 2 clamps.

(3) Engage the guide.

(4) Connect the connector bracket with the bolt.

Torque:

7.0 N·m {71 kgf·cm, 62 in·lbf}

(5) Install the protective cover.

(j) for Windshield Glass Side:

(1) w/ Pre-collision System or EC Mirror:

2. INSTALL SUN ROOF OPENING TRIM MOULDING (for Moon Roof)

(a) Align the alignment mark on the sun roof opening trim moulding with the notch of the roof headlining assembly and install the sun roof opening trim moulding. NOTICE: After installation, check that the corners fit correctly. HINT: Make sure that the tape is positioned as shown in the illustration.

*a Alignment Mark *b Notch *c Tape

3. INSTALL VISOR HOLDER LH

(a) Install the visor holder LH as shown in the illustration.

Install in this Direction

4. INSTALL VISOR ASSEMBLY LH

NOTICE:

Make sure to install the visor assembly LH with its arrow facing the front of the vehicle.

(a) Connect the visor assembly LH to the visor holder LH.

*1 Visor Holder LH

(b) for "TORX" Screw:

(1) Using a T25 "TORX" socket wrench, install the visor assembly LH with the 2 screws.

(c) except "TORX" Screw:

(1) Install the visor assembly LH with the 2 screws.

5. INSTALL VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.

6. INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

7. INSTALL ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

(a) Install the 2 clips to the assist grip.

(b) Temporarily install the 2 assist grip covers to the assist grip as shown in the illustration.

(c) Engage the 2 clips to install the assist grip assembly as shown in the illustration.

Install in this Direction

(d) Engage the 4 claws to install the assist grip cover LH and assist grip cover RH. NOTICE: Make sure that the clip is engaged securely.

*1 Assist Grip Cover LH *2 Assist Grip Cover RH

8. INSTALL REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the assist grip assembly.

9. INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the assist grip assembly.

10. INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Click here

11. INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Click here

12. INSTALL SPOT LIGHT ASSEMBLY (for LED Type)

Click here

13. INSTALL ROOM LIGHT ASSEMBLY (for Bulb Type)

Click here

14. INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

Click here

15. INSTALL ROOF CONSOLE BOX ASSEMBLY

Click here

16. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

for UA80E:

Click here

for UB80E:

Click here

for UB80F:

Click here

17. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here

18. INSTALL INNER ROOF SIDE GARNISH LH

(a) Install 3 new clips to the inner roof side garnish LH.

(b) Engage the 2 guides as shown in the illustration.

Install in this Direction

(c) Engage the 3 clips to install the inner roof side garnish LH as shown in the illustration.

Install in this Direction

19. INSTALL UPPER CENTER PILLAR GARNISH LH

(a) Install a new clip to the upper center pillar garnish LH.

(b) Engage the 3 guides and clip as shown in the illustration.

Install in this Direction

(c) Install the upper center pillar garnish LH with the 2 clips.

20. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and 3 clips to install the lower center pillar garnish LH as shown in the illustration.

Install in this Direction

21. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Click here

22. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Click here

23. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

24. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the guide and 6 claws to install the rear door scuff plate LH as shown in the illustration.

Install in this Direction

25. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.

(b) Install a new clip to the front pillar garnish LH.

(c) Engage the front pillar garnish clip to the front pillar garnish LH. HINT: Make sure that the front pillar garnish clip is engaged correctly.

*1 Front Pillar Garnish Clip *2 Front Pillar Garnish LH

(d) w/o Front No. 3 Speaker:

(1) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.

Install in this Direction

(e) w/ Front No. 3 Speaker:

(1) Connect the connector.

(2) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.

(f) Engage the clip and front pillar garnish clip to install the front pillar garnish LH as shown in the illustration.

*1	Front Pillar Garnish Clip
	Install in this Direction

CAUTION:

Make sure to position the strap of the curtain shield airbag assembly LH below the engagement holes of the clips of front pillar garnish LH as shown in the illustration, otherwise the curtain shield airbag assembly LH will not be able to deploy properly.

HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.

26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

27. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the claw and clip as shown in the illustration.

Install in this Direction

(b) Install the cowl side trim sub-assembly LH with the clip.

28. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the guide and 10 claws to install the front door scuff plate LH as shown in the illustration.

Install in this Direction

29. INSTALL INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

30. INSTALL UPPER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

31. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

32. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

33. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.

34. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

35. INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

36. INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

38. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

39. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

40. INSTALL REAR SEAT ASSEMBLY (for Fixed Seat Type)

Click here

41. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Click here

42. INSTALL FRONT SEAT ASSEMBLY LH

for Manual Seat:

Click here

for Power Seat:

Click here

43. INSTALL FRONT SEAT ASSEMBLY RH

for Manual Seat:

Click here

for Power Seat:

Click here