Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001TVSK
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: LIGHTING (EXT): LIGHTING SYSTEM: High Beam Headlight Circuit; 2021 - 2024 MY Camry [10/2020 -        ]

High Beam Headlight Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Check the operation of the low beam headlights. If the low beam headlights do not operate normally, refer to Problem Symptoms Table.

    Click here 2021 MY Camry [10/2020 - 08/2021]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE 2022 - 2024 MY Camry [08/2021 -        ]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*

    Click here 2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

    • *: w/ Smart Key System

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Head Light Hi

High beam headlights

OFF or ON

-

Body Electrical > Main Body > Active Test

Tester Display

Head Light Hi

OK:

High beam headlights illuminate.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2021 MY Camry [10/2020 - 08/2021]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE 2022 - 2024 MY Camry [08/2021 -        ]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE

NG

2.

INSPECT DIM RELAY

(a) Inspect the DIM relay.

Click here 2018 - 2024 MY Camry [06/2017 -        ]; LIGHTING (EXT): RELAY: ON-VEHICLE INSPECTION

NG

REPLACE DIM RELAY
OK

3.

CHECK HARNESS AND CONNECTOR (POWER SOURCE - DIM RELAY)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

2 (DIM relay) - Body ground

Always

11 to 14 V

5 (DIM relay) - Body ground

Always

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K52 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (DIM relay) - K52-13 (DIM)

Always

Below 1 Ω

1 (DIM relay) or K52-13 (DIM) - Body ground

Always

10 kΩ or higher
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR