Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001TCVM
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2021 - 2024 MY Camry [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Tracing Assist System

2021 - 2024 MY Camry [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic View Monitor System

2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Rear door glass sub-assembly
  • Rear door glass run

Initialize power window control system

  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry [03/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS:

Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

5. REMOVE REAR ARMREST ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

8. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

10. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

11. REMOVE REAR DOOR PANEL PROTECTOR

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

12. REMOVE REAR DOOR GLASS RUN

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

13. DISCONNECT REAR DOOR WEATHERSTRIP

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR LOCK: REAR DOOR LOCK: REMOVAL+

14. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

15. REMOVE REAR DOOR QUARTER WINDOW GLASS

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

17. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

(a) Apply protective tape around the rear door belt moulding assembly as shown in the illustration.

Protective Tape

(b) Disengage the 5 claws and guide to remove the rear door belt moulding assembly as shown in the illustration.

Remove in this Direction (1)

Remove in this Direction (2)