Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001TA75
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL; 2021 - 2024 MY Camry [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Tracing Assist System

2021 - 2024 MY Camry [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic View Monitor System

2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

  • Wear protective gloves. Sharp areas on the parts may injure your hands.
  • Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here 2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2023 - 2024 MY Camry [08/2022 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS:

Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

CAUTION:

  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • If an airbag deploys for any reason, it may cause a serious injury.

3. REMOVE REAR SEAT HEADREST ASSEMBLY LH

(a) w/ Removable Headrest:

(1) Remove the rear seat headrest assembly LH.

4. REMOVE REAR SEAT HEADREST ASSEMBLY RH

(a) w/ Removable Headrest:

(1) Remove the rear seat headrest assembly RH.

5. REMOVE REAR SEAT CUSHION ASSEMBLY

(a) Lift the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks from the rear seat cushion lock hooks.

*a

Rear Seat Cushion Frame Hook

Place Hand Here

Remove in this Direction

NOTICE:

Be sure to hold the parts of the rear seat cushion assembly directly next to the rear seat cushion frame hooks when lifting it. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

HINT:

When lifting the rear seat cushion assembly, make sure to hold the area shown in the illustration.

Standard Measurement:

Area

Measurement

A

245 mm (9.64 in.)

(b) Loosen the bolt and separate the rear seat inner belt assembly RH and rear center seat outer belt assembly as a set from the anchor part of the floor panel.

(c) Remove the washer and bolt to disconnect the rear seat inner belt assembly RH.

(d) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly as shown in the illustration.

(e) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly through the rear seat cushion assembly as shown in the illustration.

(f) Remove the rear seat cushion assembly as shown in the illustration.

Remove in this Direction

6. REMOVE REAR SEAT CUSHION LOCK HOOK

(a) Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

Remove in this Direction

HINT:

Use the same procedure for the RH side and LH side.

7. REMOVE REAR SEATBACK ASSEMBLY LH

(a) Fold the rear seatback assembly LH forward.

(b) Remove the 2 bolts.

(c) Disengage the 2 guides and remove the rear seatback assembly LH.

NOTICE:

Be careful not to damage the vehicle body.

8. REMOVE REAR SEATBACK ASSEMBLY RH

(a) Fold the rear seatback assembly RH forward.

(b) Remove the 2 bolts.

(c) Disengage the 2 guides and remove the rear seatback assembly RH.

NOTICE:

Be careful not to damage the vehicle body.

9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Disconnect the rear door opening trim weatherstrip LH.

10. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

(a) Disconnect the rear seat outer belt LH from the rear seat shoulder belt guide LH.

(b) Disconnect the connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

*a

White Housing Lock

*b

Yellow CPA

Slide

(1) Push down the white housing lock and slide the yellow CPA as shown in the illustration. (At this time, the connector cannot be disconnected yet.)

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.

(2) Push down the white housing lock again and disconnect the connector.

(c) Remove the bolt.

(d) Disengage the hook and remove the rear side seatback assembly LH.

NOTICE:

Be careful not to damage the vehicle body.

11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

12. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.