| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001TA6Y |
| Model Year Start: 2021 | Model: Camry | Prod Date Range: [10/2020 - ] |
| Title: SEAT: REAR SEAT ASSEMBLY (for Fixed Seat Type): REMOVAL; 2021 - 2024 MY Camry [10/2020 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Tracing Assist System |
|
|
Pre-collision System |
|||
|
Memorize steering angle neutral point |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
-
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for A25A-FKS:
Click here
for 2GR-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
3. REMOVE REAR SEAT CUSHION ASSEMBLY
(a) Lift the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks from the rear seat cushion lock hooks.
|
*a |
Rear Seat Cushion Frame Hook |
|
Place Hand Here |
|
Remove in this Direction |
NOTICE:
Be sure to hold the parts of the rear seat cushion assembly directly next to the rear seat cushion frame hooks when lifting it. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.
HINT:
When lifting the rear seat cushion assembly, make sure to hold the area shown in the illustration.
Standard Measurement:
|
Area |
Measurement |
|---|---|
|
A |
245 mm (9.64 in.) |
|
(b) Loosen the bolt and separate the rear seat inner belt assembly RH and rear center seat outer belt assembly as a set from the anchor part of the floor panel. |
|
|
(c) Remove the washer and bolt to disconnect the rear seat inner belt assembly RH. |
|
|
(d) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly as shown in the illustration. |
|
|
(e) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly through the rear seat cushion assembly as shown in the illustration. |
|
(f) Remove the rear seat cushion assembly as shown in the illustration.
|
|
Remove in this Direction |
4. REMOVE REAR SEAT CUSHION LOCK HOOK
(a) Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
|
|
Remove in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
5. REMOVE REAR SEATBACK ASSEMBLY
(a) Disconnect each rear seat outer belt from the rear seat shoulder belt guide RH, rear seat shoulder belt guide LH and rear seat center shoulder belt guide.
|
(b) Disconnect the 2 connectors. |
|
(c) Remove the 4 bolts.
(d) Disengage the 3 hooks to remove the rear seatback assembly as shown in the illustration.
|
|
Remove in this Direction |
|
|